FORTIN 87751 Mazda B Series Remote Starters and Alarm Systems Installation Guide

REV.: 20220114
Guide # 87751
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION

87751 Mazda B Series Remote Starters and Alarm Systems

Vehicle functions supported in this diagram (functional if equipped)

| BYPASS FIRMWARE VERSION
VERSION LOGICIELLE CONTOURNEMENT
71.[44] MINIMUM| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11| | Hood trigger (Output Status).
---|---|---|---|---
| Program remote
---|---
FUNCTION| MODE| DESCRIPTION
---|---|---
2| 2| Unlock Pulse Time : Single 1.5 sec
20| 2| Trunk output : Unlock before trunk pulse 0.5 sec
| Parts required (Not included)
1X 1K Ohm Resistorode
---|---

MANDATORY INSTALL

* HOOD
PIN
CONTACT
DE CAPOT| | HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE
REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.| | SECURITY STICKER

---|---|---|---|---

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

WIRING CONNECTION

PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 1/2

| Press and hold the
programming button:
Insert the 6-Pin Main connector.
 The LEDs will alternate
between BLUE, RED, YELLOW
& BLUE/RED flashes.
---|---
| Release the programming
button when the LED is RED.
If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
| Insert the required remaining connectors.
| Wait 3 seconds.
Turn the first functIonal key to the ON/RUN position.
| Turn the ignition to the OFF position
and remove the first key.
| Turn the second functIonal key to the ON/RUN position.
Wait 3 seconds.

PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 2/2

| Turn the ignition to the OFF position and remove the second key.
---|---

The RED LED will flash rapidly ten (10) times.
If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

Manual transmission: Remove the jumper.

Transmission manuelle:
The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE 1/2 |

DCRYPTOR PROGRAMMING PROCEDURE 2/2

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE | MISE À JOUR INTERNET
This guide may change without notice. See www.fortin.ca for latest version.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>