MEAN WELL XBG-100 Constant Power Mode LED Driver User Guide
- June 13, 2024
- MEAN WELL
Table of Contents
100W Constant Power Mode LED Driver
XBG – 100 series User’s Manualhttp://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf
Features
- Full power output at 70~100% constant current range operation
- Wide input range 90 ~ 305VAC with active PFC function
- Metal housing design with 1P67
- Multiple dimming functions: 3 in 1(0-10V/PWM/Resistor)
- Dimming circuit with Isolated for latest safety regulation
- Surge protection with 6KV/4KV
- Typical lifetime>50000 hours and 5 years warranty
- AC input cable with connector for flexible installation
Applications
- LED bay lighting
- LED stage lighting
- LED spot lighting
- Explosion-proof lighting
- Type HL LED driver for class I division 2.
GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx
Description
XBG-100 series is a 100W AC/DC LED driver featuring the constant power mode.
XBG-100 operates from 90~305VAC and offers with different rated current
ranging between 1750mA and 2780mA. Thanks to the high efficiency up to 92%,
with the finless design, the entire series is able to operate for -40°C~+85°C
case temperature under free air convection. The design of metal housing and
IP67 ingress protection level allows this series to fit both indoor and
outdoor applications. Moreover the innovative environment-adaptive capability
allows this series to reliably light on the LEDs for all kinds of application
environments. XBG-100 series comply with the latest version of
IEC61347/IEC60598-1 and UL8750 international safety regulations. The output
and dimming circuit are also completely in accordance with the new regulations
with isolation to ensure the safety of both users and luminaire system during
installation.
Model Encoding
Type | lP Level | Function | Note |
---|---|---|---|
A | lP67 | constant power adjustable via built-in potentiometer | ln Stock |
AB | lP67 | constant power adjustable via built-in potentiometer + 3 in 1 | |
dimming function (0~10Vdc, 10V PWM signal and resistor) | ln Stock |
SPECIFICATION
MODEL | XBG-100- – |
---|---|
OUTPUT | DEFAULT CURRENT |
RATED POWER | 100W |
CONSTANT CURRBS EN/ENT REGION | 27 ~ 56V |
FULL POWER CURRENT RANGE | 1750~2780mA |
OPEN CIRCUIT VOLTAGE (max.) | 60V |
CURRENT ADJ. RANGE | 875~2780mA |
CURRENT RIPPLE | 3.0% max. @rated current |
CURRENT TOLERANCE | ±5% |
SET UP TIME | Note.4 |
INPUT | VOLTAGE RANGE |
127 ~ 431VDC
(Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR (Typ.)| PF≧0.97 / 115VAC, PF≧0.95 / 230VAC, PF≧0.92 /
277VAC at full load (Please refer to “Power Factor Characteristic” section)
TOTAL HARMONIC DISTORTION| THD< 10% (@ load≧50% at 115VAC/230VAC
,@load≧75% at 277VAC) Please refer to “TOTAL HARMONIC DISTORTION (THD)”
section
EFFICIENCY (Typ.)| 92%
AC CURRENT (Typ.)| 1.1A / 115VAC 0.5A / 230VAC 0.42A /
277VAC
INRUSH CURRENT(Typ.)| μCOLD START 50A(twidth=400 s measured at 50%
Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER| 8 unit(circuit breaker of type
B) / 14 units(circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.75mA / 277VAC
STANDBY POWER CONSUMPTION| Standby power consumption<0.5W for AB-Type
PROTECTION| OVER POWER| 105-150%
Hiccup mode, recovers automatically after fault condition is removed
SHORT CIRCUIT| Constant current limiting or Hiccup mode, recovers
automatically after fault condition is removed
OVER VOLTAGE| 61 ~ 78V
Shut down output voltage, re-power on after fault condition is removed to
recover
OVER TEMPERATURE| Shut down output voltage, re-power on after fault
condition is removed to recover
ENVIRONMENT| WORKING TEMP.| Tcase=-40 ~ +85℃(Please refer to
“OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.| Tcase=+85℃
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH non-condensing
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 60℃)
VIBRATION| 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X,
Y, Z axes
SAFETY & EMC| SAFETY STANDARDS| UL8750(type”HL”), CSA C22.2 No.
250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS
EN/EN62384;
IS15885(Part2/Sec13); GB19510.1,GB19510.14; IP67;EAC TP TC 004 approved
WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC I/P-PE:2KVAC O/P-PE:1.5KVAC
ISOLATION RESISTANCE| I/P-O/P, I/P-PE, O/P-PE:100M Ohms / 500VDC / 25℃/
70% RH
EMC EMISSION| Parameter| Standard| Test Level/Note
Conducted| BS EN/EN55015(CISPR15),GB/T17743| —–
Radiated| BS EN/EN55015(CISPR15),GB/T17743| —–
Harmonic Current| BS EN/EN61000-3-2,GB/T17625.1| Class C @load≥50%
Voltage Flicker| BS EN/EN61000-3-3| —–
EMC IMMUNITY| BS EN/EN61547
Parameter| Standard| Test Level/Note
ESD| BS EN/EN61000-4-2| Level 3, 8KV air ; Level 2, 4KV contact
Radiated| BS EN/EN61000-4-3| Level 3
EFT/Burst| BS EN/EN61000-4-4| Level 3
Surge| BS EN/EN61000-4-5| 4KV/Line-Line 6KV/Line-Earth
Conducted| BS EN/EN61000-4-6| Level 3
Magnetic Field| BS EN/EN61000-4-8| Level 4
Voltage Dips and Interruptions| BS EN/EN61000-4-11| >95% dip 0.5 periods, 30%
dip 25 periods,
95% interruptions 250 periods
OTHERS| MTBF| 2871.3K hrs min.| Telcordia SR-332(Bell core) ;188.8K hrs min.| MIL-HDBK-217F (25℃)
LIFETIME| Note.5| 50000 hrs min.
DIMENSION| φ130mm 56mm(DH)
PACKING| 0.8Kg; 16pcs/ 14.8Kg/1.57CUFT
NOTE| 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. De-rating may be needed under low input voltages. Please refer to Stack CHAR Cartelistic sections for details.
3. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
4. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
5. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃ or less.
6. To fulfill requirements of the latest ErP regulation for lighting fixture, this LED drive can only be used behind a switch without permanently connected to the mains.
7. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com
8. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
9. Products sourced from the Americas regions may not have the PSE/CCC/BlS/KC logo. Please contact your MEAN WELL sales for more information.
10. For any application note and lP water proof function installation caution, please refer our user manual before using. https://[www.meanwell.com/Upload/PDF/LED_EN.pdf](http://www.meanwell.com/Upload/PDF/LED_EN.pdf)
※ Product Liability Disclaimer: For detailed information, please refer to https://[www.meanwell.com/serviceDisclaimer.aspx](http://www.meanwell.com/serviceDisclaimer.aspx) File Name:XBG-100-SPEC 2022-02-18
BLOCK DIAGRAM
DRIVING METHODS OF LED MODULE
-V Operating Area
© XBG-100
DIMMING OPERATION
# 3in 1 dimming function (for AB-Type)
- Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0~10VDC, or 10V PWM signal or resistance.
- Direct connecting to LEDs is suggested. Itis not suitable to be used with additional drivers.
- Dimming source current from power supply: 100pA (typ.)
- Applying additive 0~ 10VDC
- Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
- Applying additive resistance:
Note
- Min. dimming level is about 8% and the output current is not defined when 0%< lout<8%.
- The output current could drop down to 0% when dimming input is about 0Q or 0Vdc, or 10V PWM signal with 0% duty cycle.
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
TOTALHARMONIC DISTORTION (THD)
EFFICIENCY vs LOAD
XBG-100 series possess superior working efficiency that up to 92% can be
reached in field applications.
X 1750mA Model, Tease at65C
LIFE TIME
INSTALLATIONS
Caution
- Please inspect the appearance of the driver if the package is damaged. There should not be any cracks.
- Please do not drop or bump the driver.
- All screws including the suspension screw should be paired with a spring washer and locked tight.
- The entire luminaire, including the driver, should be limited to 10Kg or less.
- The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation.
- Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.
MECHANICAL SPECIFICATION
A-Type(AC Cable with fixed cable)
AB-Type(AC Cable with fixed cable)
- TC: Max. Case Temperature. (case temperature measured point)
- Ta: Ambient Temperature measured point
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>