MINKA LAVERY 2434-84 Winsley 4 Light 30 Inch Wide Vantage Bathroom Vanity Light Installation Guide
- June 13, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 2434-84 Winsley 4 Light 30 Inch Wide Vantage Bathroom Vanity
Light
Product Information
The product is a fixture with the item number 2434-84/878. It is designed for installation in a junction box and is suitable for use with medium base (E26) bulbs up to 60 watts each, or CFL or LED equivalents (bulbs not included). The fixture has a circular strap, a back plate, a glass shade, and finials for securing the back plate. It also includes mounting screws, a ground screw, and wire connectors.
Product Usage Instructions
- Before starting the installation, shut off the power at the fuse box or circuit breaker.
- Remove the old fixture, including the mounting hardware.
- Carefully unpack the new fixture and lay out all the parts on a clean area.
- Thread the mounting screws into the pre-drilled holes in the circular strap. Make sure the screws are spaced the same distance apart as the holes in the back plate. Tighten them with nuts.
- Attach the circular strap to the junction box using the junction box screws. Ensure that the side of the circular strap marked “GND” faces out.
- Connect the electrical wires as shown in Fig.2. Secure all wire connectors. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap using the green screw provided.
- Neatly tuck the wire connectors into the junction box.
- Place the back plate onto the mounting screws and secure it with finials.
- Unscrew the metal ring and place the glass shade onto the socket cup. Secure the glass shade with the metal ring.
- Install up to four medium base (E26) bulbs, CFLs, or LED equivalents in accordance with the fixture specification. Make sure not to exceed the maximum wattage rating.
- Once the installation is complete, return power to the junction box and test the fixture.
Note: The illustration provided in Fig.1 is for installation purposes only and may or may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
WARNING ! SHUT POWER OF FATFUSE OR CIRCUIT BREAKER .
MOUNTING THE FIXTURE (Fig.1)
-
Shut off power at the fuse box or circuit breaker and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
-
Thread mounting screws (B) into pre-drilled holes in circular strap (G) spaced same distance apart as holes in back plate and tighten with nuts (E). The length of mounting screws (B) may be adjusted if necessary.
-
Attach circular strap (G) to junction box (not included) using junction box screws (D). The side of circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig.2)
-
Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (G) using the green screw provided.
-
Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1) -
Place back plate onto mounting screws (B) and secure with finials (A).
-
Unscrew metal ring (F) and place glass shade (I) onto socket cup (H). Secure glass shade (I) with metal ring (F).
-
Install (4) four medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>