FORTIN 108601 EVO-ALL and Hyundai Push-to-Start Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
VEHICLE YEARS
Vehicle functions supported in this diagram (functional if equipped)
Immobilizer bypass
Lock | Door Status |
---|---|
Unlock | Hood Status* |
Arm | Trunk Status |
Disarm | Foot-Brake Status |
Parking Light | Hand-Brake Status |
Tachometer | OEM Remote monitoring** |
HYUNDAI
| FIRMWARE VERSION| To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
D6| Push-to-Start
| IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| | Hood trigger
(Output Status).
NOTES
It is recommended to install a remote-starter equipped with an alarm since
after installation, the OEM alarm will no longer be functional.
**OEM Remote monitoring
The vehicle’s OEM remote will operate while the engine is running.
Parts required (Not included) 2X 1Amp Diodes
MANDATORY INSTALL
* HOOD PIN
| HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE
REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
---|---
Notice: the installation of safety elements are mandatory. The hood pin
is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRING CONNECTION
PROGRAMMING PROCEDURE
| alternatively illuminate.
Press and hold the programming button:
Insert the 4-Pin (Data-Link) connector.
→ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
If the Red LED is not ON solid
---|---
| go back to step 1. Release the programming button when the Red LED
is ON.
→ If the Red LED is not ON solid disconnect the 4-PIN Data-Link harness (Black
connector) and go back to step 1. Insert the required remaining connectors.
| Insert the required remaining connectors.
| Press and release the programming button once (1x).
→ The RED LED will flash 5 times and pause.
| Press and release the Push-to Start button twice to turn ON the
ignition.
Turn the key to the Ignition
→The Blue LED will flash rapidly.
Key bypass programmed.
→The Red LED will flash 10 times rapidly.
CAN-Bus programmed.
| Press and release the Push-to Start button once to shut off the
ignition.
→The Blue LED will turn off.
| The module is now programmed.
Use the remote of the remote starter / security system to test all the
supported features and ensure all the features are properly programmed.
REMOTE STARTER FUNCTIONALITY
| All doors must be closed.
Remote start the vehicle.
---|---
Unlock the doors with either:
- The OEM remote
- The remote-starter remote
- Or the proximity remote
| |
---|---|---
Enter the vehicle with the SMART-KEY.| DO NOT PRESS THE BRAKE PEDAL.
Press and release the Push-to-Start button once.| Press the brake pedal.
The vehicle can now be put in to gear and driven.
If the Smart-Key is not detected the vehicle will shut down.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC
ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Venue
Push-to-Start 2023
This guide may change without notice. See
www.fortin.ca for latest version.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>