Westinghouse 77886 Jax fan Wall Control Instruction Manual

Westinghouse 77886 Jax fan Wall Control

Product Information

The Westinghouse Jax fan Wall Control is designed for use with the following models: 78003, 78127, 78614, and 78409. It is a wall control rated for a maximum of 8 Amps fan load at 120  olts. The control requires a three- conductor cable with a ground wire to be run between the control wall box and the ceiling fan outlet.

Product Usage Instructions

1. Before installing the wall control, verify the proper operation of the ceiling fan wall control to avoid any damage that may void the warranty.
2. Disconnect power to the ceiling fan at the main electric panel by removing the fuse or switching the circuit breaker to the OFF position. Make sure to turn off the electricity at the main fuse or circuit breaker box.
3. Remove the rotary speeds knob and on/off switch knob from the control.
4. To remove the front cover, follow these steps:
   • Position the cover over the ON/OFF button with the four protrusions inserted into the groove provided on the extrusion ribs.
   • Gently push the cover upwards so that the two protrusions on top of the cover are higher than the extrusion ribs.
   • Take out the top half of the cover and then push it downwards to make the other two protrusions come out of the extrusion ribs.
   • Take out the entire cover.
5. Refer to wiring diagram 1 for wiring and installation of the wall control to the outlet box using the supplied screws. Make sure not to connect any neutral (WHITE) wire to this control as it can cause damage.
6. Check all connections to ensure they are tight, including the ground wire, and that no bare wire is visible at the wire connectors except for the ground wire.
7. With the wall control set to the off position, restore electricity to the circuit from the circuit breaker panel or fuse box.

How to Operate Your Wall Control:

1. Turn the wall control ON using the push button on the Westinghouse Jax Fan Wall Control. Set the fan to High speed and allow it to run for 30 minutes to normalize the motor temperature.
2. To adjust the fan RPM, locate the adjustment screw on the control’s front panel (refer to diagram 3). Use a small flat blade screwdriver to slowly turn the adjustment screw clockwise to decrease RPM and counter-clockwise to increase RPM. Make small adjustments and allow the fan to speed up or slow down before making the next adjustment.

Installation & Operating Instructions for the Westinghouse Jax fan Wall Control
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

• 2-Wire
• Infinitely Variable
• 8 Amps
• Faceplate Included

SAFETY PRECAUTIONS

WARNINGS:

• To avoid fire, shock, and serious personal injury, follow all instructions carefully. all instructions carefully before installation. Save this Owner’s Manual for future reference.
•  Before servicing or cleaning the ceiling fan, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device such as a tag, to the service panel.
• WARNING: Do not install or use this unit if any part is damaged or missing.
• Fans operated with this control must be suitable for use with solid-state speed controls. Refer to the ceiling fan owner’s manual to confirm if your fans are permitted to use solid-state speed controls.
• WARNING: Use of this control with some ceiling fans could result in fire, shock and serious personal injury. Use this speed control only with Westinghouse 78003, 78127, 78614 and 78409 series ceiling fans that are suitable for use with solid-state speed controls.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION & NOTICE

• To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

• Make certain no bare wires are exposed outside the wire connectors.

• All wiring must conform to National and Local Electrical Codes.

• This wall control is rated for Max. 8 Amps fan load at 120 volts.

• All wiring must conform to National and Local Electrical Codes. If you feel that you do not have enough electrical wiring knowledge or experience, have your fan control installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.

• Use of this control with some ceiling fans could result in fire, shock, and serious personal injury. Use this fan control only with capacitor speed controlled ceiling fans only.
  The WHITE neutral wires inside the electrical box must be connected together for proper operation of the wall control. NEVER connect the WHITE neutral wires to the Westinghouse Jax Fan Wall Control.

• Warning! Do not connect any neutral (WHITE) wire to this control.

MAKING THE ELECTRICAL CONNECTIONS AND INSTALLATION

NOTE: Installation of this control requires that the three-conductor cable with ground wire be run between the control wall box and the ceiling fan outlet.

1. Verify proper operation of the ceiling fan wall control before installation. Improper wiring can damage the control and will void the warranty.

2. Disconnect power to the ceiling fan at the main electric panel. Remove the fuse or switch the circuit breaker to the OFF position.
   Warning! Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

3. Carefully remove the rotary speeds knob and on/off switch knob from the control (Refer to the diagram 1).
   

4. The front cover is installed by positioning the cover over the ON/OFF button with the four protrusions inserted into the groove provided on the extrusion ribs, gently push the cover upwards so that the two protrusions on top of the cover are higher than the extrusion ribs, take out the top half of the cover and then push it downwards to make the other two protrusions come out the extrusion ribs, take out the entire cover.(Refer to diagram 2).
   

5. According to the wiring diagram 1 for wiring and installation of the wall control to outlet box use the screws supplied. Refer to below detail for wiring.
   NOTE: Refer to the diagram on the back of the wall control.

6. Connect the black wire marked with “TO MOTOR L” from the wall control to the BLACK wire from the fan.

7. Connect the black wire marked with “AC IN L” from the wall control to the AC 120V HOT wire.

8. Use the wire connectors provided to secure the connections

9. Connect the GREEN/Ground wire from wall control to the ground wire from wall box.

10. Secure the wall control to the wall box using the two #6-32” x 3/4” screws provided.
    Warning! Do not connect any neutral (WHITE) wire to this control. Incorrect wiring WILL damage this control.

11. Reinstall the front cover, engage the two protrusions on bottom of the cover into the groove provided on the extrusion ribs, gently push the cover upwards so that the two protrusions on the front cover are higher than extrusion ribs, press the cover owards the wall and push it down-wards so that the two protrusions on top of the cover are inserted into the groove provided on the extrusion ribs. Install the ON/OFF button, be sure the ON/OFF button is free to operate without interference from the cover, install the rotary speed switch button.
    Warning! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire.

12. With the wall control set to the off position, restore electricity to the circuit from the circuit breaker panel or fuse box.

HOW TO OPERATE YOUR WALL CONTROL:

1. Turn the wall control “ON” using the push button on Westinghouse Jax Fan Wall Control. Set the fan to “High” speed and allow the fan to run for 30 minutes to normalize the motor temperature.

2. It is recommended that the fans rotate at a minimum of 60 RPM on low speed to avoid stalling the motor. To adjust the fan RPM, locate the adjustment screw on the control’s front panel (Refer to diagram 3). With a small flat blade screw driver, slowly turn the adjustment screw clockwise to decrease RPM and counter-clockwise to increase RPM. Turn the adjustment screw in small increments and allow the fan to speed up or slow down before making the next adjustment.
   

3.  Turn the fan(s) off using the Westinghouse Jax Fan Wall Control ON/OFF button.

4. Turn the control knob to the High position and depress the ON/OFF button and release. Adjust the fans speed to the desired comfort level by rotating between the low and high positions. To turn the fans off, depress ON/OFF button and release.

5. NOTE: Turning the speed control knob to high speed during start-up will assist starting the fans and avoid stalling conditions.

6.  The Westinghouse Jax fan wall control is designed to operate multiple fans without light kits. The Westinghouse Jax fan wall contorl is rated for 8.0 amps 120V full load. It is recommended the Westinghouse Jax fan wall control shall have a minimum load of 4.0 amps with fans at high speed. All ceiling fans must be completely installed before installation of the Westinghouse Jax wall control. Your new control will require a grounded electrical supply line of 120 volts AC, 60 Hz,15amp circuit.

WARNING!
To reduce the risk of fire or electric shock or damage the fan do not use this wall control together with any other additional solid state fan speed control device, or variable speed control.

TROUBLESHOOTING GUIDE

PROBLEM: WALL CONTROL FAILS TO OPERATE

Check:

• Is there power to the control unit?
• Is the control unit wired correctly?
• Are the fan and light switches set on the highest position?

LIMITED WARRANTY

The Westinghouse universal Jax fan wall control offers a limited warranty of one year from the date of purchase to the original owner against defects in material and workmanship. All spare parts are covered for ninety days only. This warranty is in lieu of all other warranties expressed or implied.
Westinghouse will repair or replace this universal Jax fan wall control if it is defective due to faulty materials or workmanship. This warranty does not cover service charges, defects resulting from accidents, damages caused through abuse or alterations or by affixing any attachment not provided with the product, improper installation or maintenance, failure of supporting devices not supplied as original mounting hardware, exposures to extremes of heat or humidity, incorrect voltage, surges in current, unauthorized repair, or failures caused by modifications of the product or the acts of third parties. See remote manual for proper installation.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouselighting.com/contact- us.

References

• Ceiling Fans | Lighting Fixtures | Lamps
• Contact Us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>