FORTIN 69321 2020 Kia Rio Push Button Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
FORTIN 69321 2020 Kia Rio Push Button Remote Starters and Alarm Systems
Product Information
- Product: KIA Rio Push to Start 2018-2023
- Model Number: GUIDE # 69321
- Description: This product is a vehicle immobilizer bypass module designed for KIA Rio models with push to start functionality. It allows for the bypassing of the immobilizer system, enabling the vehicle to start without the need for a key.
- Hardware Version: Not specified
- Firmware Version: Not specified
Product Usage Instructions
- Wiring Connection:
- Locate the 82-pin connector at the back of the fuse box in the driver’s sidekick panel.
- Connect the module’s A1 wire to the RS14 wire, which is the ground out while running out wire.
- If using data-link, connect the module’s RS7 wire to the starter wire, RS6 wire to the ignition wire, and RS5 wire to the accessory wire.
- Connect the module’s RS2 wire to the 12V battery wire.
- Connect the module’s RS1 wire to the ground/masse wire.
- Make sure to follow the appropriate wiring connections based on whether data link is required or not.
- Programming:
- Locate the programming button on the module.
- Press and hold the programming button while inserting the 4-pin (Data-Link Connector) into the module.
- The LED on the module will alternate between yellow and red.
- Release the programming button when the LED turns solid red.
- If the LED does not turn solid red, disconnect the 4-Pin connector and go back to step 1.
- Key Bypass Programming:
- Press and release the programming button 7 times in quick succession.
- The red LED on the module will flash 6 times and then pause.
- Press the START/STOP button twice to turn on the ignition without pressing the brake pedal.
- The red LED will flash rapidly 10 times, indicating that the key bypass has been programmed.
- Press the START/STOP button once to turn off the ignition.
- Testing:
- Use the remote of the remote starter or security system to test all supported features.
- Ensure that the vehicle starts and functions properly with the bypass module installed.
Note: For any further assistance or troubleshooting, refer to the user manual or contact customer support.
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
This manual may change without notice.
www.fortinbypass.com for latest version.
DESCRIPTION
WIRING CONNECTION
PROGRAMMING PROCEDURE
-
Press and hold
Insert the programming button: the 4-Pin (Data-Link Connector) connector.
The LED will alternate between YELLOW and RED. -
Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link Connector) and go back to step 1. -
Insert the required remaining connectors.
-
Press and release the programming button 7 times (7x).
-
The RED LED will flash 6 times and pause.
-
Do not press the brake pedal.
Press the START/STOP button twice to turn ON the ignition.
The RED LED will flash rapidly 10x times.
Key bypass programmed. -
Press the START/STOP button once to turn OFF the ignition.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our website on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer-safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2015, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>