FORTIN 79681 100 Degree Plug and AMP Play Remote Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
FORTIN 79681 100 Degree Plug and AMP Play Remote
Product Information:
-
Product Name: THAR-ONE-NIS5 Immobilizer Bypass T-Harness
-
Compatible Vehicles: Chevrolet City Express (2014-2017), Nissan NV200 (2012-2020)
-
Bypass Firmware Version: 72.[48] (minimum requirement for Nissan/Infiniti)
-
Remote Starter
Option: Function 31, Mode 4 – (+) Parking Light (E1), (+) Accessory (E2) -
Bypass Option: Unit Option C1
Product Usage Instructions
- To add the firmware version and options, you will need to use either the FLASH LINK UPDATER or FLASH LINK MOBILE tool, which are sold separately.
- Program the remote starter option by following these steps: – Function: 31 – Mode: 4 – Description: (+) Parking Light (E1), (+) Accessory (E2) – Description (French): (+) Feux de stationnement (E1), (+) Accessoire (E2)
- Program the bypass option by following these steps: – Unit Option: C1
- If your vehicle is not equipped with a functional hood pin, set Function A11 to OFF. This is mandatory for installation if the vehicle can be remote started with the hood open.
- Install the hood pin switch (included) if required for remote starting with the hood open.
- Ensure that the HOOD STATUS is set to A11 OFF if the hood pin switch is not installed.
- Install the module by a qualified technician as a wrong connection can cause permanent damage to the vehicle.
- Connect the transponder connector and ignition harness according to the provided wiring connection guide.
- Cut the loop for automatic transmission mode if applicable.
- Use the T-HARNESS – HARNAIS EN T THAR-NISS5 for the Nissan NV200.
- Connect the necessary wires according to the wiring diagram provided on Page 3 of the user manual.
- For the parking lights, connect the (+) PARKING LIGHTS wire to the Purple (Mauve) wire.
- For locking, connect the (-) LOCK wire to the Red (Rouge) wire.
- For unlocking, connect the (-) UNLOCK wire to the Purple (Mauve) wire.
- Complete the installation as per the provided instructions and ensure all connections are secure. Please note that these instructions are a summary of the user manual. For detailed installation instructions and diagrams, refer to the complete user manual provided with the product.
THAR-ONE-NIS5 THARNESS INSTALLATION
BYPASS FIRMWARE VERSION
VERSION LOGICIELLE CONTOURNEMENT
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool,sold separately.
MANDATORY INSTALL
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE 1/2
-
Press and hold the programming button:
Connect the 6-PIN Main harness (White connector).
The blue, Red, Yellow and
Blue & Red LEDs will alternatively illuminate.
-
Release the programming button when the LED is YELLOW.
If the LED is not solid YELLOW disconnect the 6-Pin connector (Main-Harness) and go back to step 1. -
Insert the required remaining connectors.
-
Press and release the programming button two times (2x).
The YELLOW LED will alternate between 2x flashes and a pause.
Wait until the YELLOW
LED turns ON. -
Turn the key to the Ignition ON/RUN position.
The RED LED will turns ON.
If the YELLOW and RED LED’s are not solid, remove the key and go back to step -
Repeat this step until the RED and YELLOW LED’s are solid.
Wait for the BLUE LED to flash rapidly. -
Turn the key to the OFF position.
-
Remove the key from the ignition barrel
Turn the key to the Ignition ON/RUN position
The BLUE, YELLOW and RED LED’s will rapidly alternate. -
When the YELLOW LED begins to flash rapidly: Key bypass programmed.
When the YELLOW LED begins to flash rapidly: Key bypass programmed. -
Turn the key to the OFF position.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE
STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our website on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
Module label
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>