FORTIN 45461 Ford Fiesta 2011 Push To Start Remote Starters And Alarm Systems User Manual

45461 Ford Fiesta 2011 Push To Start
Remote Starters And Alarm Systems
User Manual

REV.: 20230529
Guide # 45461
REGULAR INSTALLATION
VEHICLE YEARS

45461 Ford Fiesta 2011 Push To Start Remote Starters And Alarm Systems

ADDENDUM – SUGGESTED WIRING CONFIGURATION
Vehicle functions supported in this diagram (functional if equipped)

Immobilizer bypass with INSET*

Lock
Unlock
Arm
Disarm
Tachometer
Parking Lights
Door Status
Trunk Status
Hood Status*
Hand-Brake Status
Foot-Brake Status

FIRMWARE VERSION
71.[49] FORD MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Parts required (Not included)
1x INSET
AUTOMATIC TRANSMISSION
1x 10A Fuse Max.
2x Relay
1x 1A Diode
MANUAL TRANSMISSION
1x 10A Fuse
2x Relay
2x 1A Diode

MANDATORY INSTALL

• HOOD PIN
  HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
  A11 OFF NON
  Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
  THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

KEY CONTROL

PROGRAMMING PROCEDURE

Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.

Insert the required remaining connectors.

Do not press the brake pedal.
Press the Push-to-Start button twice to turn on the ignition.
The BLUE LED will flash rapidly.

Press the Push-to-Start button once to turn off the ignition.
The BLUE LED will turn off.
The module is now programmed.

REMOTE STARTER FUNCTIONALITY

Module label

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer  safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in  every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly,  improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing  defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
This guide may change without notice.
See www.fortin.ca for latest version.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>