FORTIN 109631 2012 Dodge Journey Push Button Remote Starters and Alarm Systems Instruction Manual

STANDALONE & THAR-CHR6 INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.
REV.: 20230531
Guide # 109631

VEHICLE
YEARS

109631 2012 Dodge Journey Push Button Remote Starters and Alarm Systems

Vehicle functions supported in this diagram (functional if equipped)

• Immobilizer bypass
• Lock
• Unlock
• Arm
• Disarm
• Parking Lights
• Hatch (Open)
• Tachometer
• Door Status
• Hood Status
• Hand-Brake Status
• Foot-Brake Status
• OEM Remote monitoring

DODGE
Journey
Push-to-start 2011-2017

| FIRMWARE VERSION
| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---

Program bypass option:
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
Program bypass option (If equiped with OEM alarm):

MANDATORY INSTALL

• HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

NOTES

NOTES 12V BATTERY

ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 5 AMP MAXIMUM.
If a parking lights (+) wire is use : that require more than 5Amp. Connect the remote-starter’s power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link.
In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

PARTS REQUIRED (NOT INCLUDED)

Notice: the installation of safety elements are mandatory.
The hood pin and the valet switch are essential security elements and must be installed.

STAND ALONE CONFIGURATION

| Program bypass option
OEM Remote Stand Alone Remote Starter:
---|---
| Program bypass option with oem remote:
| Program bypass option with RF KIT antenna:
UNIT OPTION| DESCRIPTION
---|---
| By default, LOCK, LOCK, LOCK
Par défaut, VERROUILLE,VERROUILLE,VERROUILLE
C1| OEM Remote Monitoring
H1 to H6| Supported RF Kits and select RF Kit

REMOTE STARTER FUNCTIONNALITY

| |
---|---|---
All doors must be closed.| Press the OEM remote’s Lock button 3x to remote- start (or remote-stop) the vehicle.| The vehicle will START.

REMOTE STARTER DIAGNOSTICS
MODULE RED LED

before start
x5 flash :| Hood Open

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately.

WARNING
REMOTE STARTER
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON THE VEHICLE.

DESCRIPTION

THAR-CHR7 | AUTOMATIC TRANSMISSION CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

KEY BYPASS PROGRAMMING PROCEDURE

1| Press and hold the
programming button: Insert the 4-Pin (Data-Link) connector.
↪ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---
2| Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
3| Insert the required remaining connectors.
4| Do not press the brake pedal.
Press the START/STOP button twice to turn ON the ignition.
5| Press and release the
programming button once (1x).
↪ The BLUE LED will turn off.
↪ The BLUE LED will flash rapidly (CAN1 detection).
↪ The RED LED will flash rapidly (CAN2 detection).
6 | Press and release the START/STOP button once (1x) to shut off the ignition.
↪ The BLUE LED will continued to flash rapidly.
7| Press the UNLOCK button on the OEM remote.
↪ The BLUE LED will turns OFF.
↪ Wait, the YELLOW LED will turns ON solide.
8| Remove the battery from the OEM remote
9 | Place the OEM remote (no battery) close to the front of START/STOP button exactly as shown.
Do not move the OEM remote for the following step.
10 | Press the Start/Stop button twice to turn ON the ignition.
↪ The YELLOW LED will turns OFF.
↪ The RED LED will turns ON.
11 | Press and release the START/STOP button once to shut off the ignition.
12 | Place the OEM remote (no battery) close to the front of START/STOP button as shown.
Do not move the OEM remote for the following step.
13 | Press the Start/Stop button twice to turn ON the ignition.
↪ The BLUE LED will turn off.
↪ The BLUE LED will turns ON.
↪ The RED and YELLOW LEDs will alternated.
14 | Press and release the
START/STOP button once to shut off the ignition.
↪ The RED and YELLOW LEDs will continued to alternated.
15 | Reinsert the battery in the OEM remote.
16 | Disconnect all the connectors and after the Data-Link (4-pins) connector.
17 Microsoft Windows Computer with Internet connection
Smartphone (Internet provider charges may apply)| Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE
to visit the DCryptor menu.
*Parts required (not included)
18 | AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
Test the remote starter. Remote start the vehicle.

OPTIONAL RF-KIT PROGRAMMING

PROGRAM BYPASS OPTION

OPTIONAL FORTIN RF KIT SERIES 4 OR SERIES 9 PROGRAMMING

REMOTE STARTER FUNCTIONALITY

| | | |
---|---|---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
either:
• The OEM remote
• The remote-starter
remote.| the vehicle with the Intelligent
SmartKey.
Enter| The vehicle can now be put in to gear and driven.

Module label

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797

ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE

References

• wah damn solid

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>