CLAS OC 0039 Tool To Hold The Cylinder Hood Hatchback Instruction Manual

CLAS OC 0039 Tool To Hold The Cylinder Hood Hatchback

Product Information

The OC 0039 is a tool designed to hold the cylinder hood/hatchback in place. It is manufactured by CLAS Equipements and is suitable for various applications.

Product Usage Instructions

Installation

1. Ensure that the strut shaft is free of dirt.
2. Position the clamp at the base of the shaft, inserting it near the piston. Refer to figure 2 for visual guidance.

Operation

Apply pressure on the tool by turning the pressure screw handwheel. This will help secure the cylinder hood/hatchback in place. Refer to figure 3 for visual guidance.

Maintenance

Take care of your tools by following these maintenance guidelines:

• When storing the tool outdoors, ensure it is protected from water.
• Moderately tighten the pressure screw handwheel to avoid denting the shaft.

Storage

When storing the tool, make sure it is protected from water and stored in a safe place.

Safety Precautions

• Before returning the product for any reason, including installation problems or manufacturing issues, please contact CLAS Equipements through mail at sav@clas.com, phone at +33(0)4 79 72 69 18, or visit their website clas.com. If you have changed your mind about the purchase, return the product before attempting to install it.
• If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician.
• For any action related to the tool, it is compulsory to read the instruction manual provided.
• The manufacturer guarantees the proper operation and full compliance of the product’s performance only if all the instructions in the manual are closely followed. The manufacturer shall not be held responsible for any improper uses of the product.

Technical Specifications:

• Strut shaft housing diameter: [Insert diameter]
• Weight: [Insert weight]

Manufacturer’s Information:

CLAS Equipements ZA de la CROUZA 73800 CHIGNIN FRANCE

WARNING

• Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.

Contact :

• You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com
• If you have changed your mind regarding your purchase, please return this product before you attempt to install it.

TOOL TO HOLD THE CYLINDER HOOD/HATCHBACK

INTRODUCTION

• It is compulsory to read this instruction manual before starting any kind of action.
• The proper operation and full compliance of this product’s performance is guaranteed only if all the instructions provided in this manual are closely adhered to.
• We guarantee that this product complies with the technical specifications described in this manual.
• The manufacturer shall not be held responsible for any improper uses other than those described herein.

Misuse:

• This product should only be used as described in this documentation; any other use is considered improper.
• The manufacturer accepts no responsibility for any damage caused by the incorrect or unreasonable use of the equipment.
• Moreover, misuse shall also void the warranty.

Take care of your tools:

• Be sure to store your tools in a clean state.
• Place the tools inside their original package.

SAFETY PRECAUTIONS

• Carefully read all instructions, warnings and precautions.
• During system operation, observe all safety regulations to avoid injury or equipment damage. In case of doubt regarding safety or applications, contact Clas. Failure to observe these precautions could result in serious equipment damage and personal injury.
• PRECAUTION : indicates correct operating or maintenance procedures to avoid damage to the equipment or to the surrounding environment:
• Check the correct operation of the tool and its integrity before use,
• Clean any dirt on the strut shaft, opposite to the one to be replaced, and on which to fix the clamp,
• If it is used to replace bonnet struts, wait until the engine is completely cold.
• WARNING : indicates a potential hazard that requires putting into practice the correct procedures to avoid accidents:
• When replacing bonnet struts, always wear personal protective equipment (gloves, safety goggles with side shields, safety shoes and work clothing).
• DANGERS : indicates a situation in which an action or lack of action may cause serious personal injury or even death:
• risk of cutting in the lower part of the tool (shaft housing slot),
• risk of crushing fingers between the slot and the pressure screw,
• tool falling on the body, especially the lower limbs.

APPLICATION AREA

• The mechanical properties, the shape and dimensioning for which it was designed ensure that Clas strut support clamps can be used in the automotive sector for:
• Removal and fitting of boot (tailgate) and bonnet struts on the opposite side. (fig. 1)

TECHNICAL SPECIFICATIONS

INSTALLATION

After making sure that the strut shaft is free of dirt, position the clamp at the base of the shaft, inserting it near the piston, (fig. 2)

OPERATION

• Moderately tighten the handwheel of the pressure screw on the shaft. (fig. 3)
• Carry out the removal and subsequent fitting of the strut on the opposite side.

MAINTENANCE

• Clas strut support clamps do not require particular maintenance.
• Good cleaning and storage is necessary, making sure the tool does not fall, and the slot or the pad of the pressure screw does not get damaged

STORAGE

When stored outdoors, make sure the tool is protected from water.

DANGERS

Moderately tighten the pressure screw handwheel to avoid denting the shaft.

• CLAS Equipements
• ZA de la CROUZA 73800 CHIGNIN FRANCE
• Tél. +33 (0)4 79 72 62 22 Fax. +33 (0)4 79 72 52 86
• OC 0039
• TOOL TO HOLD THE CYLINDER HOOD/HATCHBACK
• If you need components or parts, please contact the reseller.
• In case of problems, please contact your authorized technician.
• clas.com

Documents / Resources

| CLAS OC 0039 Tool To Hold The Cylinder Hood Hatchback [pdf] Instruction Manual
OC 0039 Tool To Hold The Cylinder Hood Hatchback, OC 0039, Tool To Hold The Cylinder Hood Hatchback, The Cylinder Hood Hatchback, Hood Hatchback, Hatchback
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>