CatchX Black Samurai User Guide

June 3, 2024
CatchX

CatchX Black Samurai

CatchX Black Samurai PRODUCT

INTRODUCTION

Dear Customer,
Thank you for purchasing the CatchX BLACK SAMURAI (be referred to BLACK SAMURAI hereunder) bait boat.
BLACK SAMURAI is an advanced smart fishing bait boat, which has a payload of 3kg and a range of 800 meters. With the ergonomic handle, it is easy to carry around with.
You can control BLACK SAMURAI either by our app named “Rippton” or the remoter control. Hope you will enjoy every fishing journey with company of BLACK SAMURAI.
Before we start learning how to use it, please download the Rippton App on your mobile device. You can find the Rippton App on the Google Play Store, Samsung Galaxy Apps and App Store. Installing the app requires Android System 8.0 or above and iOS 9.0 or above.

Installation of the Batteries

Use your hand or your own screwdriver to unlock the battery compartments.CatchX Black Samurai 01

Control of LED Light Belt

Double click the power button of the remote control to switch on/off both of the head LED light belt and the tail light belt.

Attach the Fishing Line

CatchX Black Samurai 02
CatchX Black Samurai 03Press the button shown in square above to open hook release mechanism which will be open for 5 seconds and close automatically. And attach the fishing line when it is open.
Note: CatchX Basic/BLACK SAMURAI Version has one antenna, and CatchX Pro Version has two antennas.

How to Use the Remote Control

Brief

BLACK SAMURAI is capable of covering 800 meters controlled by its remote control. The remote control is equipped with a display screen and buttons of different functions as the image below shows. Please refer to Section 6&7 of the User Manual for detailed function description.

Preparation of the Remote Controller
  1. Unfold the rack
  2. Unfold the antennas.
  3. Attach your mobile device to the mobile device holder clamp
Operation of the Joystick

TIP: Move the joystick to the right to the maximum extent for 3 seconds to unlock.

Releasing Burley and Hooked Fishing Line by the remote

CatchX Black Samurai 08

  • If you intend to release hopper 1, press the button HOPPER1, and long press the CONFIRM button, or long press the button Shortcut A to open hopper 1 without pressing the CONFIRM Button. Shortcut B is for hopper 2.
  • If you intend to release the hook, press the HOOK RELEASE button, wait till the screen shows “hook selected” and then long press the CONFIRM button.CatchX Black Samurai 09

How to Use Your Mobile Device to Control

Notice: Preloading the map on the APP
When using BLACK SAMURAI in any new area, before connecting the boat to your mobile device, it is always necessary to enter the Rippton app first with internet connection, enter the operation interface (refer to 5.2.1 and 5.2.2 below) to finish preloading the map where you intend to fish at.

Connection
  1. Open Wi-Fi setting on your phone and find “catchx_xxxxxx”
  2. Tap the “catchx_xxxxxx” and enter the password 12345678. This step will make your mobile device lost the internet connection.
Operation
  1. Step 1: Open the Rippton app and tap “Device” on the top.CatchX Black Samurai 11

  2. Find CatchX BLACK (2 Hoppers) and tap “Enter”.
    Before setting a mission, please check the image below to understand what each icon stands for.CatchX Black Samurai 12 The Learner Mode (sailing range limited within 300m) is automatically on the first time you enter the page. It can be turned off in Common Set.CatchX Black Samurai
13

  3. Calibration

    • After the boat connected with the APP, please tap the cog icon on top right of the APP interface to enter “COMMON SETTINGS”.CatchX Black Samurai 14
    • Tap the ellipsis icon on bottom right, then choose “CALIBRATE” after the boat has been put on the water surface and well connected to the remote. The boat will automatically finish the calibration on the water by itself.CatchX Black Samurai 15
      Note:
      It’s always necessary to calibrate BLACK SAMURAI at new locations where are 3km away from the last you have used the boat at.
  4. Set a Route for Casting Mission

    • Tap the “Mission Management” button (in square 1) on the top of left side to start setting a route for your casting mission. Press the green button to confirm (in square 2).

    • Tap the “H” button (in square 3) to set the home point for the mission. Move the map to set the “H” icon at your desired spot as the home point.
      Re-tap the “H” button to confirm.

    • After the home point has been set, long press the point you want in the green circle until the prompt box pops up.

    • Tap “Confirm”.
      Repeat the above-mentioned process if you want to add more waypoints (but no more than 2 waypoints).

    • If you want to delete the selected waypoint, tap it and then select “Delete” in the prompt box.

  5. Select the Hoppers
    There are two ways to select hoppers, which directly decides the mode of the mission: fully automatic and half automatic.

    • Fully Automatic
      Before performing the mission, tap the selected waypoint, and then tap “Hopper Selection” to confirm which hopper or fishing line to be released on which waypoint.CatchX Black Samurai 22

    • Half Automatic.
      If you start a task without selecting hoppers before the boat begins to sail, you need to confirm which hopper to be released every time the boat reaches a selected waypoint.CatchX Black Samurai 23

  6. Perform the Mission

    • Tap “Start” in the right bottom corner.CatchX Black Samurai 24

    • Slide to start. CatchX Black Samurai 24NOTE: BLACK SAMURAI will return to the home point automatically after the mission is completed.
      If you intend to cancel the ongoing mission, there are two methods:

    • tap the “Return to Home Point” button. The boat will go back to the home point set previously;

    • move the joystick on the remote control downwards for 3 seconds, the operation mode will turn to “Manual” and the boat will stay at the position it stopped.
      CatchX Black Samurai 26

  7. Release the Hook

    • When the boat arrives at the point where you want to release the hook, tap the third button on the left side. You can also select the point to release the hook when selecting the hoppers before the mission starts.
    • Slide to cast.
  8. Reset the Hoppers and Hook
    When a mission has been completed, the indicator color of the used hopper(s) and hook will turn gray from green as shown at the bottom of the left picture.
    Please tap “Reset” button to have the status of all the hoppers and hook become available again.

Charging

Bait Boat
  • Direct charging : 5.5/2.5 DC charging port (please refer to Picture1). Please note that both batteries must be inside the boat together when direct charging. It takes 4-6 hours to be fully charged; or  Charging the batteries separately (please refer to Picture2) after taking those out of the battery compartment.CatchX Black Samurai 30
Remote Control

Connect type-C side of the controller charger to the power port.
It takes 2-3 hours to be fully charged.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals