COOPER Lighting Solutions IL52435021 CoviO Linear Cove System Instruction Manual
- June 12, 2024
- COOPER Lighting Solutions
Table of Contents
COOPER Lighting Solutions IL52435021 CoviO Linear Cove System Instruction
Manual
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
DISCLAIMER OF LIABILITY: Cooperlighting assumes no liability for damages
or losses of any kind that may arise from the improper, careless, or negligent
installation, handling or use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future
reference.
NOTICE: Green ground screw provided in proper location. Do not relocate.
NOTICE: Fixture may become damaged and/or unstable if not installed
properly.
Note: Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
INSTALLATION
-
Optimize cove design detials.
Note: To optimize cove lighting, cove design must be optimized
Figure 1.
Figure 2.1
-
Plan run lengths and power drops per run length specifications below:
| Run Length Limits (ft)
---|---
Lumen Package| 05L (500lm)| 10L (1000lm)| 15L (1500lm)
Fixture Input Wattage| 5.1W| 9.9W| 14.6W
Dimming Protocol| 0-10V (STD) ELV (ELV) Triac (TR) WaveLinx (WL)| Maximum Run Length (ft) @ 120V| 140| 70| 50
DALI (5LT)| Maximum Run Length (ft) @ 277V| 300*| 170| 120
| Maximum Run Length (ft) @ 120V| 92| 47| 32
Maximum Run Length (ft) @ 277V| 216| 110| -
Unpack fixtures, cables, and mounting hardware from boxes.
Note: All installations require a beginning of run power cord with custom connector and junction box supplied by Eaton. Line voltage power supply line supplied by others. If your installation calls for the jumper cable accessory to add space between fixtures, make sure they are available. -
Prepare beginning or run for line voltage input by removing top screws to open junction box wiring compartment. Remove hole cover of desired feed location and feed line voltage power lead cable (by others) through hole. Trim power feed to desired length. Connect power lead cable and input driver wiring to female connector wires via wire nuts in accordance with wiring chart in Table 2 below. Green ground screw must be connected for safe operation.
Note: Minimum of 18 AWG power lead cable wires to be used.
| HOT| NEUTRAL| **GROUND *| CONTROL 1| CONTROL 2**
---|---|---|---|---|---
0-10Vdc| Black| White| Green| Purple
(0-10v +)| Pink
(0-10v +)
Wavelinx| Black| White| Green| N/A| N/A
5th light / Dali| Black| White| Green| Purple
(Dali Bus)| Purple
(Dali Bus)
ELV /Triac| Black| White| Green| Black / Red
(Dimmed Hot)| N/
Fixture must utilize a green Pigtail or a Green Through Wire for grounding.
Figure 3
-
Close junction box by tightening top screws.
-
If mounting angle is desired, place proper degree mounting under the clip before securing mounting clips.
Figure 5.1
-
Secure mounting clips with 2 screws in straight line at least 2” from wall for optimal cove lighting.
Figure 6
-
Snap male connector from beginning of run power feed into female connector of the first fixture in the run. Self closing cap of female connector must be opened for connection. Connector must “click” to ensure complete, proper connection
To disconnect, squeeze the silver tab on the male connector pull apart fixtures.
Figure 7
-
Mountings are designed to span between fixtures to assure alingnment between fixtures within the cove. Connectors have 2” standoffs to align with the cove wall and optimize cove lighting performance
-
Install fixture into mounting by making sure mounting channel in the bottom of the fixture engages with the mounting clip.
Fixture can then be rotated into place making sure the top clip engages in the upper mounting channel to secure fixture in any orientation.
Figure 9.1
Figure 9.2
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
Note: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment must
be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons.
Warranties and Limitation of Liability
Please refer to
www.cooperlighting.com/LightingWarrantyTerms
for our terms and conditions.
Costumer Support
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2020 Cooper Lighting Solutions
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IL52435021
January 29, 2020
Cooper Lighting Solutions is a registered trademark. All trademarks are property of their respective owners
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>