dji CS785U CrystalSky Wireless LCD Monitor User Guide

dji CS785U CrystalSky Wireless LCD Monitor

Disclaimer

Congratulations on purchasing your new DJITM product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of

DJI. For up-to-date product information, visit http://www.dji. com and click on the product page for this product. By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree to abide by the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and regulations, and all terms, precautions, practices, policies, and guidelines DJI has made and may make available.

DJI accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this document.

DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies.

Warning

1.  The Charging Hub is only compatible with the DJI-specified Charger. DO NOT attempt to use the Charging Hub with any other battery charger.
2.  The Charging Hub is only compatible with the DJI-specified Intelligent Battery. DO NOT attempt to use the Charging Hub with any other battery.
3.  Ensure to press the Battery Release Button before removing the battery.
4.  DO NOT attempt to touch the metal terminals on the Power Adapter.
5.  Clean the metal terminals with a dry, clean cloth if there is any noticeable buildup of dirt.

Introduction

CrystalSkyTM is designed specifically for aerial photography and can display a clear image under different lighting conditions with the built-in light- sensitive sensor. Support DJI MAVICTM, OSMOTM series (Osmo Mobile excluded), INSPIRETM series, PHANTOMTM 4 series, Phantom 3 series (Phantom 3 Professional, Phantom 3 Advanced), and MATRICETM series. Use the built-in DJI GOTM/DJI GO 4 app to control the gimbal, camera, and other features of your flight system. The app also comes with a map, a store, and a user center for configuring your aircraft and sharing your content.* Support for DJI devices will be added as testing and development continues. Visit the DJI CrystalSky product page on dji.com for a complete list.

In the Box

• CrystalSky Monitor ×1
• Intelligent Battery ×2 (CS785/CS785U) or ×1 (CS550)
• Intelligent Battery Charging Hub (WCH2) ×1
• CrystalSky User Guide ×1
• Intelligent Battery Safety Guidelines ×1
• Mounting Bracket (Optional) ×1
• Hood (Optional) ×1
• Optional parts can be purchased separately at the official DJI Online Store.

Overview

CrystalSky Monitor

1. HDMI Port
   Output HDMI video signal.

2. USB Port
   Supported extended device, e. g. U disk.

3.   Micro SD Card Slot
   Provides extra storage space for the display device, the maximum card size is 128 GB.

4. Micro USB Port
   Use a Micro USB cable to connect to the remote controller when in use, or to the PC to configure parameters via

5. DJI ASSISTANT
   To update aircraft firmware, please use the USB OTG cable.

6.  Headphone Jack

7.  Mounting Screw Hole

8.  Light-sensitive Port Built-in light-sensitive sensor.

9.  Type-C USB2.0 HS Port

10. Built-in GNSS

11. Power Button

12. Custom Button

13. Setting Button

14. Custom Button

15. Back Button

16. Battery Release Button

17. Battery Slot

Usage

Charging the Battery
Use the Inspire 2 charger for illustration. Place the battery into the standard charging hub, and connect connector B of the battery charger to the charging hub, then connect the battery charger to a power outlet (100-240V, 50/60Hz). The Charging Hub will intelligently charge batteries in sequence according to battery power levels from high to low. The buzzer will begin beeping when charging is complete. Remove the battery or turn off the Buzzer Switch to stop it. The Status LED blinks green when charging and turns solid green when fully charged.

• DO NOT charge the Intelligent Flight battery together with the Intelligent Battery when using the Inspire 2, Phantom 4 charger or Inspire 2 Car Charger .
•  USB power supply port can be used to charge a mobile device of 5V/2A.
•  Refer to the Charging Hub (WCH2) User Guide for more details.

Mounting the Battery
Put the battery into the Battery Slot, then slide it to the end until you hear a click.

Press the Battery Level Button once to check the battery level.

•  Press the Battery Release Button before removing the battery.
•  The Intelligent Battery can charge the built-in battery after mounting, which may reduce the operation time of the Intelligent Battery. The built-in battery can keep the monitor stand-by for a short period without the Intelligent Battery, so you can start the monitor fast once get the Intelligent Battery mounted. Use the CrystalSky CS785 for installation illustration.

Mounting the Monitor

DO NOT obstruct the built-in GNSS during use.

Connect the Monitor
When using the Mounting Bracket, plug the connector on the Mounting Bracket to the remote controller USB port.

When using without a Bracket, connect the Monitor to the remote controller via a Micro cable.

DO NOT use the Type-C USB 2.0 HS port and Micro USB ports as the Micro USB port will not work.

DJI GO/GO 4 App
Press the Power Button until the Monitor powers on, then enter the DJI GO/GO 4 app. Use the built-in DJI GO/DJI GO 4 app to control the gimbal, camera and other features of your flight system. The app also comes with a map, a store, and a user center, for configuring your aircraft and sharing your content.

This image is for reference only. Please refer to the actual user interface.

Specifications

Monitor

Model| CS785/ CS785U| CS550
Weight| Approx. 425 g| Approx. 228 g
Dimensions (without battery)| 208.6×147.8×17 mm| 153.76×84.94×19 mm
Dimensions (with battery)| 208.6×147.8×34.75 mm| 153.76×84.94×39.6 mm
Touch Screen| 7.85‘, IPS screen, supporting multi-point touch| 5.5‘, IPS screen,

supporting multi-point touch

Resolution| 2048×1536| 1920×1080
Brightness| CS785: 1000 cd/m2

CS785U: 2000 cd/m2

| 1000 cd/m2
Storage| CS785: ROM 64GB CS785U: ROM 128GB| ROM 32GB

To comply with local regulations, the operation frequencies of both 5150-5250MHz and 5725-5850MHz are not available in some countries All Mavic and Osmo series products require a Mounting Bracket (purchased separately from the official DJI Online Store) to be compatible with CrystalSky. Note that only CS550 is compatible with Mavic and Osmo series products. The 57 W battery charger does not supply enough power to charge batteries and other devices connected to the USB port simultaneously. DO NOT use the USB port to charge another device when charging batteries.

Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance

EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro- compliance

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is free. The owner of old appliances is responsible to bring the appliances to these collection points or to similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances. This device is restricted to indoor use when operating in the 5150-5250MHz frequency range in all EU/EFTA member states and Turkey. The Adopted Trademarks HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.http://www.dji.com/support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>