arte confort NEUS L Novelties Wall Solar Instruction Manual

arte confort NEUS L Novelties Wall Solar

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person

While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

• The product must only be installed by an authorized electrician and in compliance withlocal, regional and state electricity regulations.
• Check if the electrical specifications of this device ore compatible with your installation.
• Turn off the power before installing or repairing the fan.
• The fan must be properly grounded to avoid the risk of electric shock.
• Use and unauthorized technical modifications could suppose a risk of injury.
• The fan must be connected to a ‘2.30V SOHz power supply.
• Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
• Be careful while working near the spinning blades.
• Never connect the fan to a power point but to the ceiling itself.
• The fan must be installed so that the blades ore at least ‘2.,3 meters above the ground.
• The fan must be hung from a structure capable of supporting a weight of at least 50 kg . The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.
• Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling. Keep in mind that the larger this space, the better the fan’s air flow will be.
• This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture.
• Never install the appliance in a room with a high degree of humidity.
• The fan must not be started in a room with a gas appliance running at the same time.
• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance of the device.
• Children should not play with the device.
• To reverse the direction of the blades, do it while moving.
• Do not insert any object into the fan bladeswhile they are rotating. This can damage them and alter the balance of the fan and the device can fall down.
• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

The instructions and safety regulations in this manual cannot prevent all conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses and enjoys the product

BEFORE INSTALLATION

• Open the box ovoiding the use of blodes or “cutters” to avoid scratching the fan components.
• Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.
• It is advisable to mount the fan on the floor or a surface large enough so that no component falls.
• Identify all parts before beginning assembly.

TOOLS NEEDED

Not included. It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
• Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint­free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.
If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well- being.
Thanks for taking care of the environment.

This product contains a light source of energy efficiency class E – (EU) 2019/2015

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply.

1. The fan does not start
2. Replace the remote control batteries if they are exhausted or not suitable.
3. Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
4. Resynchronize the remote control.
5. Check that the electrical connections are correct (must be carried out by a licensed electrician)
6. Check fuses and switches, that the installation has voltage and it reaches the fan.
7. The fan doesn’t start but the light does.
8. With the fan off, check with your hand that the blades turn freely.
9. The fan makes excessive noise while rotating a
10. Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
11. Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
12. If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.
13. The fan wobbles
14. Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
15. Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.
16. The fan does not give air or the air flow is insufficient
17. Check that the blades are not mounted backwards.
18. Check that the blades rotate in the correct direction (Summer/ Winter).
19. Avoid nearby objects that may impede air circulation.
20. Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.
21. The light does not turn on
22. Check the bulb is not blown, otherwise replaces it with a new one.
23. If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

COLOR TEMPERATURE MEMORY

• The fan has color temperature memory of the light. This function allows you to maintain the same color temperature when the fan light is turned on again.
• To change the color temperature, turn off the light by pressing the “Lamp ON/OFF” button once and turn it on again by pressing the button again within 2 seconds.
• Turn the light off again by pressing “Lamp ON/ OFF” and after 15 seconds turn it on again, it will keep the last selected temperature

REMOTE CONTROL

• WINTER/SUMMER MODE
  Reverse the direction of rotation of the blades to change to summer mode or winter mode.

• LAMP ON/OFF I SYNCHRONIZATION
  Turns the light and synchronization on or off (see section “Control synchronization”).

• FAN ON/OFF
  Turn the fan on or off.

• SPEED REGULATOR
  Increases or decreases the turning intensity of the blades.

• PROGRAMMING
  Sets the hours of fan operation (l, 2 or 4 hours).

SPEAKER

1. Activate
   To activate the loudspeaker, if it is switched off, press and hold the button for 3 seconds and beep twice.

2. Synchronise
   Once the speaker and Bluetooth are turned on, you can find the device in the Bluetooth settings and connect it. After successful connection the device will beep once. The audio is not affected if the lights or fan are on or off, all three are controlled independently.

3. Turn off
   To cancel the speakerphone press the “Speaker button again for 3 seconds to turn it off.

4. Unsynchronise
   When the speakerphone is turned on, it will automatically connect to a nearby device that has been previously paired (in the Bluetooth on state). When the phone is disconnected from the Bluetooth connection, the speakerphone will beep twice.

BREEZE MODE

• Activate the breeze mode that alternates smoothly between soft and fast speeds (from speed l to 3) to create a greater sensation of comfort.
• To activate the breeze mode, activate the fan using the “ON/OFF” button on the fan and then press the “Breeze mode” button.
• For cancel breeze mode press the “Breeze mode” button again, the fan will return to the rotation speed selected before the breeze mode. You can also press the “ON/OFF” button of the fan to completely stop the rotation of the blades, when IIyou turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed.
• The remote control is synchronized from the factory you only need to re-synchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

BATTERIES

The remote control batteries are not included.
The required battery model is 2x AAA .
Remove the batteries from the controller if it is not going to be used for a long time.

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized, you only need to resynchronize the remote if you have lost synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

A REMOTE CONTROL TO A NEW FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light (\’?0°)” during 3 seconds until you hear the signal. Control range: 8-l0m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut off the current until all fans stop and wait 30″

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light (\’?0°)” on each fan during 3 seconds until you hear the signal. If they are within a radius of less than l0m (control range: 8-l0m), all will synchronize at the same time.

A REMOTE CONTROL TO A FAN

(Example for two fans, applicable to a larger number of fans)

1. **Cut the fan A current***
   Be sure to cut the fan A current (the one we want to remove the synchronization) and wait 30″.

2. **Cut the fan B current***
   Be sure to cut off fan B (the one we want to synchronize) and wait 30″.

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button “ON/OFF light (‘\t•)” during 3 seconds until you hear the signal to synchronize remote control B with fan B.

4. **Cut the fan B current***
   Be sure to cut the fan B current and wait 30″.

5. Restore the fan A current
   When you restore the fan A and within 10 seconds, press the synchronization button “ON/OFF light (‘\’)).0)” during 3 seconds until you hear the signal to synchronize remote control A with fan A.

6. Repeat the steps
   Repeat steps with each fan you have and want to individualize its remote control.

To cut the current you can press the individual Fon switch. If there is not, disconnect the quick connect cables from the fan.

LIDIA
SYNCHRONISATION OF TWO REMOTE CONTROLS TO A FAN

TWO REMOTE CONTROLS TO ONE FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″.

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control A
   Within 10 seconds, press the synchronization button “ON/OFF light (<1)1 •• )” during 3 seconds until you hear the signal. Control range: 8-l0m.

4. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″.

5. Restore the current
   Past 30″ re-establish the current.

6. Synchronize the remote control B
   Within 10 seconds, press the synchronization button “ON/OFF light (<1)1 •• )” during 3 seconds until you hear the signal. Control range: 8-l0m.

PARTS OF A FAN

SCREW GUIDE

SCREWS FOR THE ROOF

SCREWS FOR BLADES

INSTALLATION

SPARE PARTS

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchose receipt or invoice

DESCRIPTION ****

CONTROL BY APP

1. APP DOWNLOAD

2. You will need to download the “ulomp” opp to your mobile device (smartphone) from the mobile application distribution platform corresponding to the operating system of your mobile device.

3. SYNCHRONISATION OF THE “ULAMP” APP

4. Opening the application
   Open the application once it has been installed on the smartphone.

5. Activate Bluetooth and Location Activate Bluetooth and Location from the APP or from your mobile phone settings.

6. Add device
   On the main screen of the application, press the button with the symbol

7. Search and link device
   When the device you want has appeared in the search, press “Add” and then “Confirm”. Once you have the device on your screen, you can edit its name and press “Save·.

8. Synchronise device
   Wait for the download of the “Control Panel” to complete.
   When it has uploaded 100%, you will have your device linked and your control panel will appear.

9.  BOTONES

10. Configuration

11. RGB light control screen
    Access to the RG B light control screen.

12. White light control screen
    Access to the white light control screen.

13. ON/OFF

14. Colour wheel
    Touch circle where the colour can be adjusted.

15. RGB colours
    Selection of preset RGB colours.

16. Light intensity
    Adjusts the light intensity.

17. Colour
    Access to the light colour control screen.

18. Ambient scenes
    Access to the ambient scenes. The colour and light intensity varies depending on the scene you choose.

19. Timer
    Access to the timer for switching off the light.

20. DESYNCHRONISATION

21. To unsynchronise the device, press the “Settings” button and the “Delete” button.

WARRANTY

The motor of this fan is guaranteed for 8 years and 3 years for the rest of the components. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well as this instruction manual.
Keep the purchase receipt and the instruction manual.

The warranty of this product does not apply if the defects of the device have been caused by:

• Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages … )
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional parts or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the fan.

Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice.

It is not possible to synchronise more than two controllers to one fan. www.arteconfort.com
If you have any questions, problems or missing components, consult your dealer. You can also contact us through the email info@orteconfort.com or through the contact form available on our website.
www.arteconfort.com
ARTECONFORT HOTEL SL.
Ctra. Andaluda, 6
45224 Sesena N uevo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>