eyc-tech FTM06D Inline Type Air Flow Meter User Manual

June 12, 2024
eyc-tech

eyc-tech FTM06D Inline Type Air Flow Meter

Product Information

  • The eyc-tech Measuring Specialist is a versatile product that enhances your capability with sensor technology.
  • It is designed to measure various parameters including air flow, humidity, dew point, differential pressure, liquid flow, temperature, pressure, level, air quality, and signal meter.

Product Usage Instructions

  1. Ensure that the device is properly connected to a power source.
  2. Familiarize yourself with the different measurement parameters and their corresponding symbols indicated in the user manual.
  3. To measure air flow, place the sensor in the desired location and follow the specific instructions provided in the user manual.
  4. For humidity measurement, ensure that the sensor is properly calibrated and follow the instructions for accurate readings.
  5. To measure dew point, differential pressure, liquid flow, temperature, pressure, level, air quality, or signal meter, refer to the corresponding sections in the user manual for detailed instructions.
  6. When using the device, make sure to follow all safety precautions and guidelines provided in the user manual.
  7. If you encounter any issues or require further assistance, please refer to the troubleshooting section of the user manual or contact our customer support at www.eyc-tech.com.

Note: The above instructions are a general guide. Please refer to the complete user manual for detailed instructions specific to your model.

Safety Precautions

  • Please read this Specification carefully, prior to use of this, and keep the manual properly, for timely reference.

Solemn Statement :

  • This product can not be used for any explosion-proof area.
  • Do not use this product in a situation where human life may be affected. eyc-tech will not bear any responsibility for the results produced by the operators!

Warning!

  • Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
  • This product must be operated under the operating conditions specified in manual to prevent equipment damages.
  • Please using the product under the ordinary pressure, or it will influence safe problem.
  • This product must be operated under the operating condition specified in this manual to prevent equipment damages.
  • This product must be operated under the normally atmospheric condition to prevent equipment damages.
  • To prevent products damage, always disconnect the power supply from the product before performing any wiring and installation.
  • All wiring must comply with local codes of indoor wiring and electrical installation rules.
  • Please use crimp type terminal.
  • To prevent personal injury, do not touch the moving part of product in operation.
  • It may cause high humidity atmosphere during the product was breakdown. Please take safety strategy.

Panel Operation Flow

eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-
fig-1

Connection Diagram

eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-
fig-2

Installation instructions

eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-
fig-3

RS-485 and Modbus

  • FTM06D-I integrate a RS-485 interface for digital communication as an option feature.
  • Based on Mod bus protocol makes the general convenience on PLC, HMI and PC connection. For Mod bus protocol information please download the file from website.
  • Besides the PLC, HMI application, the user software provide the device setting and data logging function, it also can free download from website.

Technical Data

  1. Max. network size : 32 transmitters
  2. Communication : with COM-Port (serial interface) of PC
  3. Max. network expansion : 1200m (3937ft) total length at 9600 baud
  4. Transmission rate : 9600, 19200, 38400, 57600, 115200 Baud
  5. Parity : None, Even, Odd
  6. Data length : 8 bit
  7. Stop bit : 1 or 2 bit
  8. Factory default Station address= 1, Data format= 9600, N81

Software and calibration operation step

User may download the configuration software on eye web site. Please decompress the application prior to execute it. Operating System requirements: above Windows XP. Other application program requirements : above Microsoft Office 2003

  1. Hardware connection: Connect the FTM06D-I to PC through USB to RS-485 or RS-232 to RS-485 converter
  2. Check the COM port number from Device Manager in Computer Management. e.g. COMl in illustration
  3. Open the FTM06D-I UI, go to function II Interface 11 , click item Config and then setting COM port, BAUD rate, data format and Station ID, pressed Apply 11 for connectioneyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-5
  4. Scan RS-485 connection
    • Open the FTMO6D-I UI, go to function ” Interface” , click item “Config” and then setting COM port, pressed “Scan” bottom for scan devices and pressed ” Close and Export” when the interested devices found.eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-6
    • Pick up the device that you want to connect to and then press “Apply” to go .
  5. Setting on Analog Output

In the group of OUT1, Output tab. The output1 related setting could be found.

  1. Quantity: Flow Velocity, Flow Volume and Sensor Temperature
  2. Response rate: 0 … 100 100 : filter off , 90 : filter = 60 second 80 : filter = 120 second, etc.
  3. Analog type : 0… 20 mA / 4… 20 mA (if output current) / 0 … 10 V (if output voltage)
  4. Range for Upper and Lower
  5. Alarm Mode: Check the box if analog output pretend a alarm switch output
  6. Alarm Trigger Point: Upper and Lower
  7. Alarm Output Level: Upper and Lowereyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-7

Setting on PNP/PNP Output (Optional, Only Available if Function Equipped)

In the group of OUT2, Output tab. The PP/PP switch output related setting could be found.

  1. Quantity: Flow Velocity, Flow Volume and Sensor Temperature
  2. Response rate: 0 … 100 • 100 : filter off › 90 : filter = 60 second • 80 : filter = 120 second, etc.
  3. Alarm Mode: High Activate or Low Activate
  4. Range for Upper and Lower
  5. Alarm Point: Upper and Lower
  6. Delay Time : On Delay Time and Off Delay Time (seconds)eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-8
  7. Setting on Frequency Output (Optional, Only Available if Function Equipped)

In the group of OUT2, Output tab. The Frequency output related setting could be found.

  1. Quantity: Flow Velocity, Flow Volume and Sensor Temperature
  2. Response rate: 0…100 › 100 : filter off › 90 : filter = 60 second • 80 : filter = 120 second, etc.
  3. Frequency: Upper and Lower
  4. Measures: Upper and Lower
  5. Alarm Mode: The output would be switch between upper and lower correspond to measures
  6. Alarm Point: Upper and Lower
  7. Alarm Output : Upper and Lowereyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-9
  8. Setting on Impulse Output (Optional, Only Available if Function Equipped)

In the group of OUT2, Output tab. The Impulse output related setting could be found.

  1. Quantity: Flow Velocity, Flow Volume and Sensor Temperature
  2. Response rate: 0…100 • 100 : filter off • 90 : filter = 60 second • 80 : filter = 120 second, etc.
  3. Impulse Duration : High and Low
  4. Measures: Upper and Lower
  5. Impulse Value: The valence of single impulse quantity
  6. Impulse Unit: m°, Liter, mL, mm?, ft°, inch?, gal,us (Gallon, us), gal,uk (Gallon, uk)eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-10

Setting on RS-485, Process Parameters and offset adjustment

There are 4 groups in setting tab. The description of each item as below.

Process Parameters:

  1. Temperature of normalcondition
  2. Pressure of working condition
  3. Relative Humidity of working condition % Offset Adjustment :
  4. flow rateoffset
  5. temperature offset
  6. flow ratecut off
  7. flow rate slope adjustment, default 1 Modbus Protocol:
  8. station ID
  9. Baud Rate
  10. Date Frame
  11. Flash memory write protect Miscellaneous:
  12. Password of keypad menu
  13. LED brightness
  14. Display Alternate Period: the first field for quantity unitduration, the seconds field for quantity measure duration (seconds)eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-11

Data display and logging

  1. Assign Temperature Unit: °C / °F
  2. Assign Flow Volume Unit : Nm3/h, L/min
  3. Display Decimals
  4. Clear Measure Plot Chart
  5. Time scale of plot
  6. Vertical scale of plot
  7. Export all logging data since device is connected
  8. Start/Stop data loggingeyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-12

Device Information

  1. Model Name of Device
  2. Firmware Version of Device
  3. Serial Number of Device
  4. Firmware Checksum
  5. Calibration Date
  6. Flow Offset
  7. Temperature Offset
  8. Flow Calibration Range
  9. Temperature Calibration Pointseyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-13

Totalizer

  1. Flow Volume Rate
  2. Volume Accumulation Totalizer 1
  3. Volume Accumulation Totalizer 2
  4. unit of counter 1
  5. unit of counter 2
  6. Main switch of totalizer
  7. Function switch of totalizer 1
  8. Function switch of totalizer 2
  9. Ser/Reset Totalizer 1
  10. Set/Reset Totalizer 2eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-fig-14

Inspection and maintenance

Maintenance

  • Since this product is inspected and calibrated for high accuracy at the factory before shipment, no calibration on the installation site is necessary when this product is installed
  • For inspection and maintenance follow the instructions below:
  • (a) Periodic inspection
  • Periodically inspect this product for its sensing accuracy, and clean the cover Set the period between inspections based on atmospheric dust and other contaminants in the installation environment
  • (b) Sensor maintenance
  • Do not damage sensor surface during maintenance process
  • (c) Troubleshooting
  • If any problem occurs during operation, refer to the table below for appropriate solutions

Troubleshooting

eyc-tech-FTM06D-Inline-Type-Air-Flow-Meter-
fig-15

eyc-tech Measuring Specialist

  • enhance your capability with sensor technology
  • Air flow  Humidity Dew point Differential pressure Liquid flow
  • Temp. Pressure Level Air quality Signal meter
  • Tel.: 886-2-8221-2958
  • Web :www.eyc-tech.com
  • e-mail :info@eyc-tech.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

eyc-tech User Manuals

Related Manuals