laia TP-200 WIN PTZ Full HD Telepresence Equipment with Windows 10 User Guide
- June 6, 2024
- laia
Table of Contents
laia TP-200 WIN PTZ Full HD Telepresence Equipment with Windows 10
Attention
Please read the user manual careful and follow the installations carefully when using this equipment. Keep this manual for reference. Before connecting the power plug of this device to the external power, please confirm the power voltage value. The voltage is DC19V .
Please use the camera in suitable temperature and humidity. The temperature of is 0°C to +40°C and temperature is <90%. Prevent foreign matter from entering the device and do not spill corrosive liquids on the device to prevent danger.
During transportation, storage and installation, it should be protected from
heavy pressure, severe vibration and immersion, causing damage to the product.
Please do not disassemble the devices without authorization. The relevant work
should be done by qualified repair person.
Please use a soft, dry cloth to clean the camera. In case of stubborn dirt, wipe it with a mild detergent. Do not use strong or abrasive cleaner to avoid scratching the device casing and lens, affecting image quality.
This is A class A product which may cause radio interference in the living environment. In this case, users may be required to take practical measures against interference.
Packing List
When unpacking, please check and confirm all attachments that should be provided.
Product Introduction
Product Appearance – interfaces
| NO | Function |
|---|---|
| 1 | Lens |
| 2 | Power Lamp |
| 3 | Switch |
| 4 | Power port |
| 5 | Mini-DP Port |
| 6 | HDMI output port |
| 7 | USB 3.0 |
| 8 | Network Port |
| 9 | Line in/Out Mic |
| 10 | RS-232 |
| 11 | USB 2.0 |
After the camera connect to the power supply, it will automatically turn on,
or it can be turned on manually by power switch in the power-on state.
The red and green lights are always on during power-on self-test.
The green light is on during normal operation.
The green light flashes when the remote control is controlled.
Remote control switch system can be controlled by the power button of the
remote control.
Features
| Feature | Description |
|---|---|
| Imagen Sensor | SONY 1/2.8 Progressive CMOS |
| Effective Pixels | 3.10 Megapixel |
| Resolution | U3:YUY2:320×240,640×480,800×600, |
| HD | 1280×720,1920×1080 |
| Signal System | PAL/NTSC |
| Lens | 12X optical zoom, f=3.9mm(wide angle end)～46.8 mm(far end) |
| Horizontal View Angle | 72.5°(W)~7.4°(T) |
| Focus System | Auto/Manual |
| Minimun Ilumination | 0.1Lux |
| Iris | Auto/Manual |
| Shutter Speed | 1/1～1/10,000s |
| Gain | Auto/Manual |
| White Balance | Auto/ Indoor/Outdoor/Manual |
| Image Effect | Full color/Electronic flip |
| S/N Ratio | ≥50db |
| Pan | 355°(max. speed:80°/s) |
| Tilt | -30° to +30°(max. speed: 60°/s) |
| Preset position | 9 preset positions by IR remote controller |
| Video input | 2 x USB 3.0，1 x USB 2.0 |
| Feature | Description |
| --- | --- |
| Video Output | 1HDMI 1Mini-DP |
| Network interface | Wire:1000M port,(10/100/1000M Adaptive) |
| Control method | Remote control,USB internal control |
| Power | DC-IN 19V 3.42A |
Connection instructions
Please check if the connection is correct before starting the camera.
Attention please:
If the preset number 1 is set, after the camera powered, the camera’s
pan/tilt/zoom will automatically call the preset point 1 . If the preset
number 1 is not set, the camera will return to the HOME position, that is, the
lens will return horizontally and vertically to the front, and the zoom will
be minimized.
Use the Remote Control
- Camera Select
- Focus (auto or normal)
- M-Open: Open the menu
- Back light
- Power
- Std Rev: (press L/R Direction Set, and then press 1 or 2)
- Presets (press PRESET then press 1-9 for set up preset position).
- Reset: Press RESET and then press 1-9 for eliminate preset position.
- Zoom
- Pan-tilt Reset
- Pan-tilt: HOME for return middle position
- L/R Direction SET
- IR Transmit
- Close the MENU
Maintenance Description
The Menu
Main menu
COM SETTING: Comunication settings PTZ SETTING: PTZ settings
PICTURE SETTING: Image settings VIDEO FORMAT: Video format
VERSION: Version of firmware
FACTORY RESET: Restore factory defaults SAVE AND EXIT: Save and exit.
Communication menu:
PATH: cannot be set
PROTOCOL: Visca/PELCO-P/D/VISCA2
ADDRESS: Set the camera communication address ID
BAUD RATE: set the serial communication baud rate2400/4800/9600/19200/
38400/115200
DIV GRADE: set the speed range of the PTZ movement
SPEED ACC: set the movement acceleration of the PTZ
PTZ Menu
DZOOM: Digital zoom: ON / OFF
FOCUS MODE: AUTO / MANUAL
REMOTE SPEED: set the speed of the PTZ Movement
REMOTE ACC: Set the movement acceleration of the PTZ
PTZ FLIP: set image flip: ON / OFF
Image MENU
AE MODE: set exposure mode
WB MODE: White Balance: AUTO / INDOOR / OUTDOOR / ONE PUSH / ATW / MANUAL
NR: set the noise: OFF / LOW / MIDDLE / HIGHT BRIGHT: value of the screen:
1-15 SATURABILITY: set the color of the image: 1-14 ACUTANCE: set the acuity
of image: 1-15 GAMA: set the gamma of image: 1-4
HUE: show the current hue
MIRROR: mirror: ON / OFF
FLICK: flick of image: OFF / 50 Hz / 60 Hz.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>