TREBLAB FX100 Portable Bluetooth Speaker-User Guide

TREBLAB FX100 Portable Bluetooth Speaker

Specifications

• SPEAKER TYPE: Outdoor, Soundbar, Subwoofer
• CONNECTIVITY TECHNOLOGY: Wireless
• POWER SOURCE: Battery Powered
• BATTERY LIFE: 35 Hours
• WATER RESISTANCE LEVEL: Waterproof
• BATTERY: Up to 35 hours playtime (moderate volume) Up to 16 hours (100% volume), 7200 mAh 3.7V, rechargeable Li-Ion Input 5V / 1A, Output 5V / 1A
• CHARGING TIME: Up to 10 hours
• WIRELESS CONNECTION VERSION: 5.0, HFP, A2DP, AVRCP, GAVDP, AVDTP, SPP,AVCTP
• SIGNAL RANGE: 33ft/10m
• OUTPUT POWER: 5Wx2
• FREQUENCY RESPONSE: 80Hz- 20KHz
• WATER RESISTANCE: IPX4
• POWER/CHARGING PORTS: USB 2.0, Micro USB
• VOICE ASSISTANT ACTIVATION: Supported by the double press of the PHONE button

Introduction

With a tough TREBLAB FX100 outdoor speaker made for extreme sports and adventures, go anywhere on earth. To always ensure quality, it is weatherproof, shockproof, and IPX4 waterproof. connect to iOS and Android smartphones quickly. Sync with cellphones when at the beach or the pool, as well as while riding a bike, a boat, or a motorbike. Play the biggest classics from your personal collection or the FM radio in your area. On a single charge, you can listen for up to 35 hours. Connecting to the 7200 mAh powerbank incorporated into the TREBLAB FX100 will instantly charge your smartphone. You can Utilize the TWS mode on the FX100 to pair it with another Bluetooth speaker to get an amazing surround sound experience.

WHAT’S IN THE BOX

1. User’s manual
2. Insert card
3. Speaker
4. Carabiner
5. 5mm Audio cable
6. Round TREBLAB sticker
7. Charging cable

BUTTONS AND PARTS

Disconnect from the source device – Press the PLAY/ PAUSE button for 2 seconds.

SETTING UP YOUR FX100

Turn ON

Press and hold the POWER button for 3 seconds. You will hear the “BLUETOOTH MODE” voice prompt and the BLUE and RED LED light will start flashing.

Turn OFF

Press and hold the POWER button for 2 seconds. You will hear the “POWER OFF” voice prompt and the flashing BLUE LED light will turn OFF.

WIRELESS PAIRING

Make sure TREBLAB FX100 is charged and that the 3.5mm audio cable is not plugged in.

1. Turn on your speaker by pressing and holding the POWER button for 3 seconds. You will hear the “POWER ON” and “BLUETOOTH MODE” voice prompt and the LED light will start flashing RED and BLUE indicating that the speaker is in pairing mode.
2. Activate the Bluetooth mode on your smart device.
3. Select TREBLAB FX100 from the available Bluetooth devices list. Keep it within 3 feet/1 meter from the speaker while pairing.
4. If necessary, enter the passcode 0000 .
5. Once FX100 is successfully paired and connected, you will hear the “CNNECTED” voice prompt and the LED will light up BLUE.

REPAIRING

After the initial pairing, the speaker will automatically connect to the previously paired device when turned on again. If the reconnection does not happen automatically , the speaker will start looking for any other previously paired device within the effective distance range. TREBLAB FX100 can save up to 2 recently paired devices.

TRUE WIRELESS STEREO (TWS)- PAIRING TWO SPEAKERS

• Place two FX100 (BT5.0 version) speakers near each other (the distance should not be over 3feet/ 1meter)
• Power on both speakers. You will hear the “POWER ON” and “BLUETOOTH MODE” voice prompts.
• Press twice the PHONE button on any of the speakers this speaker will be the main one. After some time you will hear the “LEFT CHANNEL” and “RIGHT CHANNEL” prompts from TWS connected speakers.

NOTE: While the speakers are TWS paired, you can manage their functions using the buttons on both of them. You can disable the TWS mode by turning off one of the speakers or turning on the FM/Line-in mode on any of them.

AUDIO PLAYBACK

• To pause and resume the playback when connected wirelessly, press the PLAY/ PAUSE button.
• To adjust the volume, press and hold the VOLUME + or the VOLUME – button while listening to music.
• To change the track on FX1OO, press the VOLUME + or the VOLUME – button.

PHONE CALLS

TREBLAB FX1OO can be used to make and receive phone calls when connected wirelessly. Audi o playback will be paused during the calls.

the phone call.
To End a call:| Press the PHONE button during the phone call.
Multicalls’ :| Press shortly the PHONE button to answer the first call. When the second one is incoming, press

To be able to use this option, your device needs to support the multicalls management.

NOTE: For the better call quality, speak int o the microphone.

LINE-IN MODE. AUDIO CABLE CONNECTION

You can connect TREBLAB FX100 to compatible devices using the supplied 3.5mm audio cable. Turn on the speaker. Plug one end of the 3.5mmaudio cable int o the 3.5mm cable port on the edge of the speaker (under the cover) you will hear the “LINE-IN MODE” prompt. Plug the other end into the 3.5mm jack on your device.

Now you can play music and audio.

NOTE: On-device control is not supported for the VOLUME, NEXT, PREVIOUS and PAUSE functions when using the 3.5mm audio cable. Phone calls management using the PLAY / PAUSE button is not supported. To make adjustments, you will need to use your smart device.

FM MODE

TREBLAB FX100 supports the FM listening feature. FM mode can be turned on from both the Line-in and Bluetooth modes by pressing twice the POWER button. For a good level of FM signal, you will need to plug the 3.5mm audio cable. Only with the connected 3.5mm audio cable, you can receive the needed signal level!

To scan for available FM channels, press the PLAY / PAUSE button. After scanning you can change FM channels by pressing the VOLUME+/ VOLUME – button.

NOTE: If after connecting with the 3.5 mm audio cable, the speaker turned to Line-in mode, just press the POWER button twice to return to FM mode.

SOUND MODES

TREBLAB FX1OO speaker is equipped with BASS BOOST mode to improve the bass reproduction when using it outdoors. Just short press the POWER button to enable BASS BOOST mode.

CHARGING
The FX1OO speaker comes with a 7200 mAh rechargeable battery . One full battery charge provides up to 16 hours of playtime at maximum volume and up to 35 hours at 35% volume. When the battery is running low, you will hear a voice prompt.

TREBLAB FX1OO may be used while charging in Bluetooth mode, FM-mode, and Line- in 3.5 mm audio cable mode. Als o, you can use the speaker while it is used as a power bank.

To charge the speaker, plug one end of the cable supplied into the Micro USB input charging port under the rubber cover at the  side of the  speaker. Plug the other end of the charging cable into a standard USB port or wall adapt tor . It takes up to 10 hours to fully charge.

Be sure to use 5V, 2A adapter or charger. Using a power source with lower power will increase the overall charging time. If the speaker is left unused, even the fully charged battery will lose its charge over time. We recommend charging TREBLAB FX100 fully at least twice a month to maintain the sufficient battery life.

The FX100 speaker is equipped with charge level indicators – LEDs. The current charge level is displayed while charging .

1. Charge level is between 0% and 25%: the 25% indicator will begin to flash.
2. Charge level is between 25% and 50%: the 50% indicator will begin to flash.
3. Charge level is between 50% and 75%: the 75% indicator will begin to flash.
4. Charge level is between 75% and 100%: the 100% indicator will begin to flash.

POWER BANK MODE

TREBLAB FX100 inbuilt battery can be used as a power bank to charge your smartphone or tablet.

1. Connect your device to the speaker by plugging your device’s charging cable into the USB 2.0 output port at the side of FX100.
2. Press the DC OUT button to start charging. LEDs that correspond to the current battery charge level will light up.
3. There is no LED indication signal when the smart device is fully charged. Please pay attention to your device’s battery charge indicator during the charging time.

RECYCLING

The speakers can be recycled, and they should be in order to keep our planet clean. Where should you bring them? In the US , there are a couple of options:

1. Best Buy has a recycling program. Just take the broken speaker with you next time you visit a Best Buy store. This link will help you find the best location: https://fv.tvvw.bestbuy.com/site/store-locator
2. Check for other possible locations near you on these websites first enter your ZIP to find a location): https://fv.tvvw.call2recycle.org https://search.earth911.com https://recyclenation.coITTfind
3. In UK , please visit the links below for help: https://fv.tvvw.recycle-more.co.uk/,https://fv.tvvw.recyclenow.com1ocal-recycling

SAFETY RULES

• Don’t disassemble or modify your speaker for any reason. Doing this may cause the speaker to malfunction or become combustible. The damage to your device can void the manufacturer’s warranty.
• Make sure the speaker is completely dry before charging.
• Clean only with a dry cloth.
• Avoid exposing TREBLAB FX100 to extreme temperatures (below 37°F / 3°C or ab over 112°F / 45°C. Extreme temperatures can cause the deformation of the FX100 components and reduce the battery life and the lifespan of your new speaker.
• Don’t put the device’s LED lights close to humans’ or animals’ eyes.
• Do not use FX100 during a thunderstorm. Thunderstorms can cause serious malfunction and increase the risk of electric shock.

FAQs

• How is a Treblab speaker paired?
  For three seconds, hold down the POWER button. The LED will begin flashing BLUE as soon as you hear the audible trigger. Select the TREBLAB HD77 from the available devices list after turning on Bluetooth on your device. While pairing, keep it 3 feet / 1 meter away from the speaker.

• How is a Treblab speaker recharged?
  Put one end of the included cable into the Micro USB charging port hidden by the speaker’s side rubber cover to start charging the device. The opposite end of the charging wire should be inserted into a typical USB port. Up to 4 hours are needed for a complete charge. The LED light will turn on RED if the speaker is turned off.

• A Treblab speaker is water-resistant.
  Portable Bluetooth Speaker, TREBLAB FX100, Rugged Outdoor Speaker for Extreme Sports and Adventures, Metal and Rubber Body, IPX4 Waterproof, Connects to Smartphones & PCs, Up to 35 Hours/Charge.

• How can a Treblab Bluetooth speaker be reset?
  On the HD77, simultaneously press and hold the VOLUME UP and VOLUME DOWN keys for 5 seconds. The speaker will be returned to its default settings.

• How can I tell when my Treblab speaker is fully charged?
  The BLUE LED light will begin flashing as soon as you hear the cue sound. For five seconds, hold down the POWER button. The RED LED will turn on and then turn off as soon as you hear the sound cue. A full charge of the TREBLAB HD77 should be present, and the AUX wire should not be plugged in.

• What about Treblab Bluetooth speakers?
  The little TREBLAB HD77 Bluetooth speaker is a great all-purpose Bluetooth speaker for home use, parties, camping, or outdoor activities because it comes with dual subwoofers and TWS connection technology. This speaker can withstand all of your activities thanks to its IPX6 waterproof rating and shockproof durability.

• How can my Bluetooth speaker be fixed?
  Installing software updates, replacing the battery, purchasing a new cable, repairing a fractured solder joint, replacing the charging port, and replacing the charging circuit are all necessary fixes for a Bluetooth speaker that won’t charge.

• Without a charging port, how can I charge my Bluetooth speaker?
  Simply use your smartphone to charge the wireless speaker. Simply connect your smartphone to the device using the USB cable. You won’t need to worry about using a charger if you do it this way. You don’t need to buy anything more because you already carry a phone with you everywhere.

• How can I tell whether the battery on my Bluetooth speaker is full?
  If the battery is fully charged, the CHARGE indicator won’t turn on. Depending on the model, the speaker’s CHARGE indication could not turn on while it is being charged. The CHARGE indicator will turn on if the battery is charging while the speaker is off.

• How can I determine when my Bluetooth has finished charging?
  It often has a red charging indicator light. The battery is fully charged when the light goes off, indicating. You must learn how to charge a Bluetooth headset properly, that is, just when the battery is running low, if you want to get the most life out of it.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>