veratron B001032 Series Link Up Gateways User Manual

June 9, 2024
veratron

B001032 Series Link Up Gateways
User Manualveratron B001032 Series Link Up
Gateways

LINK UP GATEWAYS SERIES
LINK UP
2-in-1rev. AB

INTRODUCTION

PACKAGING CONTENT

Linkup Gateway
B00070501
Interfaces the 2-in-1 Temperature & Pressure Sensor with the NMEA 2000® network to make all the information available for any display.
Wireless configurable, the Link Up gateway can be easily set up with your smartphone and the Link Up configurator App.
Combined Oil Pressure and Temperature Sensor B000843
Measures the transmission- or engine oils temperature and pressure while providing the data to the Link Up, which translates it to the NMEA 2000® standard.

THE LINKUP GATEWAY CONCEPT
The 2-in-1-type Link Up gateway provides an easy method to convert engine information to NMEA 2000.
The devise is designed to fit one specific sensor. This sensor measures temperature and pressure. It can be applied for engine- or transmission oil.
Easily installed, the Link Up gateway replaces the original wiring, delivering power to both the Link Up device and sensor from the NMEA 2000 backbone while still being  compliant with the NMEA 2000 certification requirements.
The data are then available for being displayed on any VMH, Ocean Link, Aqua Link, or more in general on any glass cockpit NMEA 2000 display device.
Configuring Link Up gateways is simple, using a mobile device and the companion Link Up Configurator App which is available for free for Android and iOS. Each device  has a built-in passive NFC antenna, so the parameters of the sensor are wirelessly configured to type, instance and warning threshold on the mobile device which is then “tapped” against the Link Up device for instant data download.
DESIGN AND FUNCTION
The Link Up gateway has a simple but yet effective design.
The potted housing allows the unit to be installed in engine rooms, making it compliant to the ISO 8846:1990 as requested by the directive 2013-53(EC).
The standard NMEA 2000® M12 plug allows for a plug-and-play installation to the network backbone.
The sensor connection happens through a Hirschman 3way 1.2 Seal Star FA Connector, which perfectly matches the Veratrin 2-in-1 sensor, without the need of additional wiring.

SAFETY INFORMATION

WARNING
No smoking! No open fire or heat sources!

  • The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of the-art technology.
  • The instrument is designed for use in grounded vehicles and machines as well as in pleasure boats, including non-classified commercial shipping.
  • Use our product only as intended. Use of the product for reasons other than its intended use may lead to personal injury, property damage or environmental damage.  Before installation, check the vehicle documentation for vehicle type and any possible special features!
  • Use the assembly plan to learn the location of the fuel/hydraulic/compressed air and electrical lines!
  • Note possible modifications to the vehicle, which must be considered during installation!
  • To prevent personal injury, property damage or environmental damage, basic knowledge of motor vehicle/shipbuilding electronics and mechanics is required.
  • Make sure that the engine cannot start unintentionally during installation!
  • Modifications or manipulations to veratrin products can affect safety. Consequently, you may not modify or manipulate the product!
  • When removing/installing seats, covers, etc., ensure that lines are not damaged and plug-in connections are not loosened!
  • Note all data from other installed instruments with volatile electronic memories.

SAFETY DURING INSTALLATION

  • During installation, ensure that the product’s components do not affect or limit vehicle functions. Avoid damaging these components!
  • Only install undamaged parts in a vehicle!
  • During installation, ensure that the product does not impair the field of vision and that it cannot impact the driver’s or passenger’s head!
  • A specialized technician should install the product. If you install the product yourself, wear appropriate work clothing. Do not wear loose clothing, as it may get caught in moving parts. Protect long hair with a hair net.
  • When working on the on-board electronics, do not wear metallic or conductive jewelry such as necklaces, bracelets, rings, etc.
  • If work on a running engine is required, exercise extreme caution. Wear only appropriate work clothing as you are at risk of personal injury, resulting from being crushed or burned.
  • Before beginning, disconnect the negative terminal on the battery, otherwise you risk a short circuit. If the vehicle is supplied by auxiliary batteries, you must also disconnect the negative terminals on these batteries! Short circuits can cause fires, battery explosions and damages to other electronic systems. Please note that when you  disconnect the battery, all volatile electronic memories lose their input values and must be reprogrammed.
  • If working on gasoline boat motors, let the motor compartment fan run before beginning work.
  • Pay attention to how lines and cable harnesses are laid so that you do not drill or saw through them!
  • Do not install the product in the mechanical and electrical airbag area!
  • Do not drill holes or ports in load-bearing or stabilizing stays or tie bars!
  • When working underneath the vehicle, secure it according to the specifications from the vehicle manufacturer.
  • Drill small ports; enlarge and complete them, if necessary, using taper milling tools, saber saws, keyhole saws or files. Deburr edges. Follow the safety instructions of the tool manufacturer.
  • Use only insulated tools, if work is necessary on live parts.
  • Use only the multimeter or diode test lamps provided, to measure voltages and currents in the vehicle/machine or boat. Use of conventional test lamps can cause  damage to control units or other electronic systems.

SAFETY INFORMATION

  • The electrical indicator outputs and cables connected to them must be protected from direct contact and damage. The cables in use must have enough insulation and  electric strength and the contact points must be safe from touch.
  • Use appropriate measures to also protect the electrically conductive parts on the connected consumer from direct contact. Laying metallic, uninsulated cables and contacts is prohibited.

SAFETY AFTER INSTALLATION

  • Connect the ground cable tightly to the negative terminal of the battery.
  • Reenter/reprogram the volatile electronic memory values.
  • Check all functions.
  • Use only clean water to clean the components. Note the Ingress Protection (IP) ratings (IEC 60529).

ELECTRICAL CONNECTION

  • Note cable cross-sectional area!
  • Reducing the cable cross-sectional area leads to higher current density, which can cause the cable cross-sectional area in question to heat up!
  • When installing electrical cables, use the provided cable ducts and harnesses; however, do not run cables parallel to ignition cables or to cables that lead to large electricity consumers.
  • Fasten cables with cable ties or adhesive tape. Do not run cables over moving parts. Do not attach cables to the steering column!
  • Ensure that cables are not subject to tensile, compressive or shearing forces.
  • If cables are run through drill holes, protect them using rubber sleeves or the like.
  • Use only one cable stripper to strip the cable. Adjust the stripper so that stranded wires are not damaged or separated.
  • Use only a soft soldering process or commercially available crimp connector to solder new cable connections!
  • Make crimp connections with cable crimping pliers only. Follow the safety instructions of the tool manufacturer.
  • Insulate exposed stranded wires to prevent short circuits.
  • Caution: Risk of short circuit if junctions are faulty or cables are damaged.
  • Short circuits in the vehicle network can cause fires, battery explosions and damages to other electronic systems. Consequently, all power supply cable connections must  be provided with weldable connectors and be sufficiently insulated.
  • Ensure ground connections are sound.
  • Faulty connections can cause short circuits. Only connect cables according to the electrical wiring diagram.
  • If operating the instrument on power supply units, note that the power supply unit must be stabilized and it must comply with the following standard: DIN EN 61000, Parts 6-1 to 6-4.

SYSTEM INSTALLATION

WARNING
Before beginning, disconnect the negative terminal on the battery, otherwise you risk a short circuit. If the vehicle is supplied by auxiliary batteries, you must also disconnect  the negative terminals on these batteries! Short circuits can cause fires, battery explosions and damages to other electronic systems. Please note that when you disconnect the  battery, all volatile electronic memories lose their input values and must be reprogrammed.

BEFORE THE ASSEMBLY

  1. Before beginning, turn off the ignition and remove the ignition key. If necessary, remove the main circuit switchveratron B001032 Series Link Up Gateways - ASSEMBLY
  2. Disconnect the negative terminal on the battery. Make sure the battery cannot unintentionally restart.veratron B001032 Series Link Up Gateways - negative
  3. Place the device at least 300 mm away from any magnetic compass.veratron B001032 Series Link Up Gateways - magnetic

CONNECT TO THE NMEA2000® NETWORK
Connect the sensor and the Link Up gateway with the 3-pin connector (Hirschman 3way 1.2 CellStar FA Connector).
Now interface the Link Up gateway to the NMEA 2000® backbone through the dedicated plug.
Please ensure to tighten the M12 connector by screwing it onto its counterpart, so to preserve the water tightness.
A drop cable is not needed unless the total length of the Link Up device is not enough to reach the NMEA 2000® backbone. In this case it is possible to extend the total  length by using one of the accessory drop cables.
Please note that NMEA 2000® does not allow drop cables longer than 6 meters.
Refer to the NMEA 2000® standard for a proper network design.
If power from the NMEA 2000® network is received, the green LED on the Link Up housing will start flashing (see “LED notifications”).

SYSTEM INSTALLATION

CONFIGURATION

LINK UP CONFIGURATOR APP
To configure the sensor, some parameters must be calibrated through the Link Up gateway, like sensor type, engine instance or warning threshold.
This is possible through the “Link Up Configurator” smartphone App, which can be downloaded free of charge from the stores of both Android and iOS devices.
A simple and detailed explanation of the configuration process is also available as in-app instructions.
Thanks to the passive embedded NFC receiver, the Link Up gateway can be configured, as described below, without the need of power supply.

SENSOR CONFIGURATION

  1. Launch the “Link Up Configurator” App and read the actual configuration of the Link Up device by “tapping” the smartphone onto the devices wireless area (indicated
    by the red arrow).
    NOTE: The antenna position on the smartphone depends on the model. Please refer to the smartphone manufacturer manual.

  2. After the readout, the App will show the “Configuration Summary”, which displays all the current settings of the device.
    To modify the configuration, press the “Change Configuration” button.

  3. As a first step, choose your sensor type out of the options in the first box. (Sensor for engine oil or transmission oil)
    Then choose the engine instance so that the Link Up gateway will correctly transmit the data over NMEA 2000®.

  4. Now you can decide, whether you want the alarms enabled or not, and at which value these alarms should be triggered.
    Once the settings are completed, press the “Write Configuration” button to prepare the download.

  5. To download the configuration, simply “tap” the smartphone again onto the Link Up wireless area, as described on step 1.
    The configuration is instantaneously transferred to the device, and the new “Configuration Summary” is displayed.

LED NOTIFICATION

LED Behavior Description
OFF Device not powered.
ON Device configured and in operation.
Slow blink (1Hz) Device in operation with invalid or empty configuration.

Waiting for configuration by the user (factory setting).
NMEA 2000® messages are NOT transmitted.
Fast blink (5Hz)| Analogue value from the sensor out of range.
NMEA 2000® messages are being set as “invalid”.
Very fast blink (10Hz)| Device reconfiguration in progress after wireless download.

TECHNICAL DATA

LINKUP DATASHEET

Operating voltage 6 – 16.5 V
Nominal voltage 12 V (from NMEA 2000® network)
Power consumption ≤ 100 mA
NMEA 2000® LEN 2
Protection class IP X7 according to IEC60529 (when connected)
Operating temperature -30°C to 80°C
Flammability UL94-HB
Sensor cable length 90 cm
NMEA 2000® cable length 25 cm
NMEA 2000® plug Device Net Micro-C M12 5-pins – Male

SENSOR DATASHEET

Operating voltage 4.75 – 5.25V (Provided by the LinkUp)
Output Signal PWM
Temperature measuring range -40°C to 150°C
Pressure measuring range 0.5 to 10.5 bar
Protection class IP69k
Sensor plug Hirschman 3way 1.2 Seal Star FA Connector Male
Counterpart for sensor plug Hirschman 3way 1.2 Seal Star FA Connector Female

(872-858-541)

DIMENSIONS

veratron B001032 Series Link Up Gateways - DIMENSIONSveratron B001032 Series Link Up Gateways -
whether1

PINOUT

Pin No. Description
1 Shield
2 NET-S (V+)
3 NET-C (V-)
4 NET-H (CAN High)
5 NET-L (CAN Low)

Micro-C M12 5-poles plug Male, product side view

Pin No. Wire color Description
1 Red Power – 5V (Provided by the Link Up)
2 Black GND
3 Green PWM output

SUPPORTED NMEA 2000® PGNS

Description PGN
Engine Oil Temp 127489
Gear Oil Temp 127493
Engine Oil Press 127489
Gear Oil Press 127493

Any distribution, translation or reproduction, partial or total, of the document is strictly prohibited unless with prior authorization in writing from veratrin AG, except for the following actions:

  • Printing the document in its original format, totally or partially.
  • Copying contents without any modifications and stating Veratrin AG as copyright owner.

Veratrin AG reserves the right to make modifications or improvements to the relative documentation without notice.
Requests for authorization, additional copies of this manual or technical information on the latter, must be addressed to veratrin AG.

veratron B001032 Series Link Up Gateways - iconveratrin AG
Industriousness 18
9464 Rutha, Switzerland
T +41 71 7679 111
info@veratron.com
veratron.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals