BEGA 66051 Ceiling Mounted Downlight Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
**BEGA 66051 Ceiling Mounted Downlight Instruction Manual
**
Instructions for use
Application
Surface mounted downlight with symmetrical light distribution. The partially
frosted crystal glass produces an additional vertical light and supplements
the light directed downwards by multi-facetted light graphics.
Product description
- Luminaire made of aluminium alloy,aluminium and stainless steel
- BEGA Unidure® coating technology
- Colour graphite or white
- Crystal glass with thread, partially frosted
- Silicone gasket
- Reflector made of pure anodised aluminium 2 mounting holes ø 4.5mm
- Distance apart 115mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5mm, max. 5G1.5@
- Connecting terminal and earth conductor terminal 2.5@
- LED power supply unit 220-240 V x 0/50-60 Hz
- DALI-controllable
- Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
- Impact strength IK06
- Protection against mechanical impacts < 1 joule
- Safety mark
- Conformity mark
- Weight: 2.0 kg
This product contains light sources of energy efficiency class(es) D, E
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Lamp
Module connected wattage 10 W
Luminaire connected wattage 11.7 W
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C
66 051K3
Module designation LED-0839/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 1450 lm
Luminaire luminous flux 798 lm
Luminaire luminous efficiency 68,2 lm/W
66 051K4
Module designation LED-0839/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 1550 lm
Luminaire luminous flux 853 lm
Luminaire luminous efficiency 72,9 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Screw out glass from the base. Lead the mains supply cable through the cable entry into the luminaire housing. Fasten the luminaire housing with the supplied fastening material or other suitable fastening material to the mounting surface. Be sure to use the gasket rings supplied.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Make the earth conductor connection and the electrical connection. For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output. Make sure that gasket is positioned correctly. Screw the glass into the luminaire housing against the gasket.
Cleaning · Maintenance
Clean luminaire regularly with solvent-freecleansers from dirt and deposits. Do not use high pressure cleaners.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified
- persons using standard tools.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the
- LED module.
- Inspect and, if necessary, replace the luminaire gaskets.
- Defective glass must be replaced.
- Close the luminaire.
Spares
Spare glass 11 003 121 10
LED power supply unit DEV-0475/350
LED module 3000 K LED-0839/830
LED module 4000 K LED-0839/840
Reflector 76 137 2M
Gasket 83 001 467
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>