Keurig K200 Series Coffee Brewer User Manual
- June 15, 2024
- Keurig
Table of Contents
Keurig K200 Series Coffee Brewer User Manual
K200 Series Brewer
- Water Reservoir Lid
- Water Reservoir
- Top Housing
- Touch Screen/Power Button
- Brew Button
- Handle L Brew Head
- Power Cord
- Drip Tray Plate
- Drip Tray
- Pod Holder
- Housing (K and L are the Pod Holder Assembly)
- Base
Settings and Touch Screen Controls
Home Screen
- Settings Button
- Power Button
Screen for K-Cup® Pods
- STRONG (only available for coffee)
- HOT COCOA/OTHER (for select non-coffee beverages)
- Brew Size
- Power Button
Screen for K-Carafe® Pods
- KEURIG BREW Setting 1
- Brew Size
- Power Button
Brew Settings
Select the KEURIG BREW setting that matches the number on the pod lid for K-Mug® and K-Carafe® pods.
Before You Brew
Plug & Place
Remove packing tape from the brewer and plug it into a grounded outlet. Place
a large mug (12 oz. minimum) on the drip tray plate.
Power On
Press the power button. Lift the handle—remove and discard the orange shipping
disk. Lower the handle. Wait for preheating to complete, about 3 minutes.
Rinse & Fill
Remove the water reservoir lid, then lift the reservoir straight up to remove
it. Rinse the reservoir with fresh water and fill it to the MAX line. Replace
the water reservoir, making sure the lock tabs engage with the brewer. Replace
lid.
NOTE: Do not use distilled water.
Cleansing Brew Setup
Lift and lower the handle. Press the blinking brew button to start a cleansing
brew. Pour the hot water into the sink. The one-time setup process is now
complete and you are ready to brew!
Brew Your First K-Cup® Pod
Place Mug Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and place the mug on the drip tray base.
Hot Water: To dispense hot water into a mug, lift and lower the handle
without inserting a K-Cup® pod. Select your cup size then press the blinking
brew button to dispense hot water.
NOTE: Between brew cycles, the brewer may take about a minute to reheat.
Size & Strength
Select your brew size using the arrows on the screen. Select STRONG if
desired. (The STRONG setting is for coffee.) Press HOT COCOA/OTHER for select
non-coffee beverages.
NOTE: Make sure to check the instructions on the pod packaging.
CAUTION: There is extremely hot water in the K-Cup® pod during the
brewing process. To avoid injury, do not lift the handle during the brewing
process.
Lift & Insert
Lift the handle and place a K-Cup® pod in the K-Cup® pod holder. Lower the
handle completely to close the lid. Do not remove the foil lid on the K-Cup®
pod.
Brew & Enjoy
Press the blinking brew button. The button will remain illuminated while
brewing, about 1 minute. The brewer will notify you when the brew cycle is
complete. Lift the handle and dispose of the used K-Cup® pod. The brewer will
be ready to brew another cup in about a minute.
NOTE: To stop the brewing process, press and hold the power button for
one second.
Settings Menu
For all settings, press the BACK button to return to the settings menu or press the HOME button to return to the home screen. Your settings will be automatically saved.
Access Settings
Explore everything your Keurig® Plus Series Brewer has to offer by accessing
the Settings Menu. From the home screen, select the settings button. Use the
arrows to scroll through the menu. To exit, press the BACK button or HOME
button.
Choose Language
Press English, Spanish, or French to select the language.
High Altitude
To ensure your brewer works properly at higher altitudes (5,000 feet),
ENABLE the high altitude mode.
Water Filter Reminder
If you are using a Keurig® Water Filter, select ENABLE to activate the water
filter reminder.
Caring For Your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn
off and unplug your brewer before cleaning.
Brewer Exterior
Keep your Keurig® brewer looking its best by cleaning the exterior from time
to time. Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never
immerse the brewer in water or other liquids.
Water Reservoir & Reservoir Lid
The water reservoir lid and water reservoir should be periodically cleaned
with a damp, soapy, non-abrasive cloth and rinsed thoroughly. The water
reservoir lid and water reservoir should not be put into the dishwasher. Do
not dry the inside of the water reservoir with a cloth as lint may remain. If
needed, repeat the above procedures.
CAUTION: Please rinse the water reservoir thoroughly after cleaning. This
will ensure that no cleaning solutions remain in this area as they may
contaminate the water supply in the brewer.
Pod Holder
Lift the handle. Push up while grabbing the sides of the pod holder assembly.
Pull away from the brewer. Pull out the pod holder assembly and base. Press
the release buttons on both sides of the pod holder assembly. Separate the pod
holder from the housing. Clean the pod holder (1), housing (2), and base (3)
with a damp, soapy, lint-free, nonabrasive cloth and rinse thoroughly. After
all pieces are cleaned, reassemble the pod holder assembly by inserting the
pod holder back into the housing. Place the base, and then the pod holder
assembly into the brew head. Lower the handle.
CAUTION: Sharp needles. Do not put your fingers in the chamber.
Drip Tray
The drip tray can hold up to 8 ounces of overflow and should be emptied and
cleaned occasionally. To remove it, slide it toward you, keeping it level to
avoid spilling. Rinse and clean with a damp, soapy, lint-free, non-abrasive
cloth.
Cleaning Entrance Needles
Lift the brewer handle and locate the top entrance needles on the underside of
the lid. To clean both holes in the needles, hold the brewer handle in the
upward position and with your other hand, carefully insert a straightened
paper clip into the holes. Gently move it around to loosen any coffee grounds.
Lower the handle completely and run two water-only brew cycles. Do not insert
a K-Cup® pod.
TIP: Refer to support.Keurig.com for video instructions on cleaning the
entrance/exit needles.
NOTE: You can also use a Brewer Maintenance Accessory tool to clean the
entrance needles. Reach out to Customer Service to get a Brewer Maintenance
Accessory.
Cleaning the Exit Needle
If a clog arises in the exit needle, push the lever of the pod holder to
reveal the exit needle. Use a paper clip or similar tool to loosen the clog.
Rinse thoroughly with hot water. After all the pieces are cleaned, place the
base and then the pod holder assembly into the brew head. Lower the handle.
CAUTION: Sharp needles. Do not put your fingers in the chamber.
Troubleshooting
Brewer Does Not Have Power or Shuts Off
- Press and hold the power button and ensure the touchscreen is illuminated.
- Plug the brewer into its own grounded outlet. If the electric circuit is overloaded with other appliances, your brewer may not function properly.
- The brewer should be operated on its circuit, separate from other appliances.
- If the brewer still doesn’t have power, contact Customer Service.
Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and can be cleaned
using a straightened paper clip or similar tool. Clean the exit needle of the
K-Cup® pod holder. Refer to the Exit Needle care instructions. Clean the
brewer entrance needles. Refer to the Entrance Needles care instructions.
Brewing a Partial Cup
The exit needle may be clogged. Refer to the Exit Needle care instructions.
The water reservoir may have been removed during brewing. Replace the water
reservoir and perform a rinsing brew without a K-Cup® pod. The brewer may need
to be described. If you have repeated the descaling procedure on your brewer
two times and it is still only brewing a partial cup, contact Customer
Service.
Brewer Will Not Brew
After placing a pod in the pod holder, make sure the handle is lowered
completely and the touch screen displays the appropriate brew screen. Follow
the brewing instructions. If the touch screen indicates “More Water Please”
add water to the water reservoir or make sure the water reservoir is seated
properly in its base. If the touch screen indicates “More Water Please” even
after refilling, remove the water reservoir and empty the water. Then
thoroughly clean the reservoir. Fill the water reservoir to the MAX line,
return it to the brewer and ensure it is seated properly in its base. The pod
holder may need to be cleaned or the brewer may need to be descaled. Refer to
Caring For Your Brewer for instructions.
Touch Screen Alerts
“More Water Please” – If the water level is not low, remove the water
reservoir and empty the water. Clean the reservoir. Return the reservoir to
the brewer and ensure it is seated properly in its base. “Sorry, Brew
Interrupted” – Slowly lift the handle, remove the pod, lower the handle and
perform a rinsing brew.“Sorry, There is a Problem” – Coffee grounds may be
stuck in the entrance needle. Refer to Caring For Your Brewer for cleaning
instructions. “Time To Replace the Keurig® Water Filter” – Your brewer will
indicate that it is time to replace the water filter every 1,000 ounces or two
months. Once you’ve replaced the Keurig® Water Filter press YES to reset the
water filter reminder.
Recycling K-Mug® and K-Carafe® Pods
The plastic cups of K-Mug® and K-Carafe® pods can be recycled wherever #5
plastic is accepted. #5 Plastic may not be recyclable in your community today,
so please check locally with your municipality or waste hauler, or visit
KeurigRecycling.com for more information. #5 Plastic is recyclable everywhere
in Canada.
- Once brewing is complete and the pod is cool, separate the lid and filter from the cup. The filter will adhere to the lid.
- Once separated, discard the lid and the attached filter. Recycle the plastic cup wherever #5 plastic is accepted.
Descaling Your Brewer
You should describe your brewer every 3-6 months. Properly follow the descaling procedure. Depending on the mineral content of your water, calcium deposits or scales may build up in your brewer. Scale is non-toxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3-6 months helps maintain the heating element and other internal parts that come in contact with water. Calcium deposits may build up faster, making it necessary to descale more often. You should promptly describe when the touch screen indicates “Time to describe the brewer!”
Descaling Procedure
Before you begin, you will need a large ceramic mug, fresh water, Keurig®
Descaling Solution, and access to a sink. Do not use a paper cup. Ensure that
there is no beverage pod in the K-Cup® pod holder. Please allow approximately
45 minutes for the descaling procedure. Empty the water from the water
reservoir. If there is a Keurig® Water Filter, remove it and set it aside.
STEP 1
Descaling Solution Rinse Press and hold the power button to power the
brewer off. Pour the entire bottle of Keurig® Descaling Solution into an
emptied water reservoir. Then fill the empty bottle with water and pour it
into the water reservoir. Press and hold the power button to turn the brewer
back on. Place a large mug on the drip tray and run a cleansing brew by
lifting and lowering the handle, selecting the largest brew size and pressing
the brew button.
STEP 2
Descaling Rinse & Repeat Repeat the rinsing brew process until the touch
screen indicates“More Water Please”. Do not use a K-Cup® pod. Let the brewer
stand for at least 30 minutes while still on. After 30 minutes, discard any
residual solution from the water reservoir and rinse thoroughly. STEP 3: Fresh
Water Rinse Fill the water reservoir with fresh water to and not beyond the
MAX line. Place a large mug on the drip tray plate and run a rinsing brew
using the largest brew size. Do not use a K-Cup® pod. Pour the contents of the
mug into the sink. Repeat the brew process until you have completed at least
12 rinsing brews. You may need to refill the water reservoir at least one time
during this process.
NOTE
The cleaning action of Keurig® Descaling Solution may result in a “foam”
dispensed from the brewer. This is natural, as the solution is reacting with
the scale inside. For a brewer that is heavily scaled, the brewer may not fill
properly after the descaler is added. If this occurs, you may see only a small
or no output dispensed, followed by the sound of air blowing out. If this
occurs:
Turn off and unplug the brewer. If there is Keurig® descaling solution in the
water reservoir, discard the contents, rinse the water reservoir thoroughly
and refill it with water. Plug the brewer back in, power on, and repeat the
Step 3 Fresh Water Rinse cycle. The brewer should begin to function normally
as the solution is rinsed out and the scale is removed. If the problem
persists, allow the brewer to sit unplugged for at least 30 minutes before
continuing with the rinse.
NOTE: If the “Time to descale the brewer!” alert is still indicated on
the touch screen, repeat the descaling procedure.
Fully experience the benefits that come with your new Keurig® brewer at KEURIG.COM/NEW
REGISTER
your new Keurig® brewer and receive a special savings offer
DISCOVER
your favourite coffees with our customized taste quiz and get personalized
recommendations
Download PDF:Keurig K200 Series Coffee Brewer User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>