BEGA 50800.5 Indoor Wall Light Velvet Black Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50800.5 Indoor Wall Light Velvet Black Instruction Manual
BEGA
Instructions for use
Spares __
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50800.5 Indoor Wall Light Velvet Black Instruction Manual

BEGA

Wandleuchte für die Verwendung im Innenbereich
Wall luminaire for indoor use
Applique pour utilisation à l’intérieur

Instructions for use

Application

Wall luminaire · indoor luminaire for the glare free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.

Product description

Luminaire housing made of aluminium, finish Colour velvet black

Synthetic cover with light diffusing structure Reflector made of pure anodised aluminium 2 elongated fixing holes

Width 5.5 mm · 570 mm spacing 1 cable entry for through-wiring for mains cable

Connection terminal 2.5@ Earth conductor connection LED power supply unit

220-240 V x 0/50-60 Hz DC 176-264 V

DALI-controllable

Basic insulation is provided between the mains and control cables

BEGA Thermal Control®

Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire

Safety class I

Impact strength IK04 Protection against mechanical impacts < 0.5 joule

r – Safety mark c – Conformity mark Weight: 3.7 kg

This product contains light sources of energy

efficiency class(es) D

Safety

The installation and operation of this luminaire

are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.

The manufacturer accepts no liability for damage caused by improper use or installation.

If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.

To achieve an additional protection against

e. g. transients, etc. we recommend separate

overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 23.6 W
Luminaire connected wattage 27 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C
50 800.5 K3
Module designation 4x LED-1050/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 3500 lm
Luminaire luminous flux 2802 lm Luminaire luminous efficiency 103,8 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo the hexagon socket head screws (wrench size 3 mm) and lift luminaire top. Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.

Lead the mains supply cable through the cable entry of the luminaire base.

Note position of application “arrow down”. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.

Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection.

For digital control please use the connecting

terminal DA, DA.

In case this terminal is not used the luminaire will be operated at full light output.

Make earth connection (plug connection) and LED-connection between luminaire top and luminaire base again.

Note position of application of the luminaire “arrow down”.

Install luminaire top part, adjust it and tighten

screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.

The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.

Disconnect the system and open the luminaire. Undo one of the two external locking screws (Torx) in the luminaire housing and remove the lateral housing cover.

Remove the synthetic cover from the profile of

the luminaire housing.

Remove the LED module. Install the replacement LED module. Please follow the installation instructions for the LED module.

A defective synthetic cover must be replaced. Close up the luminaire again in reverse order.