BEGA 24008 Wall Light Applique Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
24 008
Wall luminaire
Instructions for use
24008 Wall Light Applique
Application
Wall luminaire with two-sided light output.
For illumination and design tasks in architecture.
The light directed downwards is intended to illuminate the wall and the
horizontal surface in front of it.
The light directed upwards is intended to illuminate the wall and ceiling
surfaces.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Clear safety glass Silicone gasket
Reflector made of pure anodised aluminium
Mounting plate with 2 fixing
holes ø 4.3 mm · 160 x 14 mm spacing 2 cable entries for through-wiring of
mains supply cable ø 7-10.5 mm, max. 5 G 1.5@
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V 0/50-60 Hz DC 176-264 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK10
Protection against mechanical impacts < 20 joule
– Safety mark
– Conformity mark
Weight: 3.2 kg
This product contains light sources of energy efficiency classes D, E
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Lighting technology
Half beam angle 17°
Lamp
Module connected wattage| 24.2 W
Luminaire connected wattage| 27.2 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 35 °C
24 008 K3
Module designation| 2x LED-0813/830
Colour temperature| 3000 K
Colour rendering index| CRI > 80
Module luminous flux| 3480 lm
Luminaire luminous flux| 2216 lm
Luminaire luminous efficiency| 81,5 lm / W
24 008 K4
Module designation| 2x LED-0813/840
Colour temperature| 4000 K
Colour rendering index| CRI > 80
Module luminous flux| 3720 lm
Luminaire luminous flux| 2369 lm
Luminaire luminous efficiency| 87,1 lm / W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo screw at wall box and remove mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material
onto the mounting surface.
Be sure to use the gasket rings supplied.
Make earth conductor connection and electrical connection to the connecting
terminal (plug connection).
The two loose plug-in terminals marked DALI are provided for digital control
purposes.
If these terminals are not assigned, the floodlight will work with full light
output.
Make earth conductor connection between luminaire and mounting plate.
Push plug into coupler as far as it will go.
Note position of application of the luminaire “arrow down”.
Make sure that gasket is positioned correctly.
Place the luminaire onto the mounting plate and fix it.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass| 14 000 211
LED power supply unit| DEV-0293/700
LED module 3000 K| LED-0813/830
LED module 4000 K| LED-0813/840
Reflector| 76 001 133
Gasket glass| 83 000 564
Gasket wall box| 83 001 081
Technical amendments reserved
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>