BEGA 50 910.6 Luminaire v/t LED Instruction Manual

Table of Contents

Before installation and commissioning, ensure that you comply with national safety regulations.
Installation and commissioning should only be carried out by a qualified electrician.
Do not modify the luminaire without proper authorization as it may void the warranty.
To protect the electronic components against overvoltage, the luminaire is equipped with built-in protection. For additional protection against transients, it is recommended to use separate overvoltage protection components.
The module-connected wattage is 23.1 W and the luminaire-connected wattage is 25.8 W.
The color temperature of the LED module is 3000 K and the colour rendering index (CRI) is greater than 90.
The module luminous flux is 3655 lm and the luminaire luminous flux is 524 lm. The luminaire has a luminous efficiency of 20.3 lm/W.
Refer to the module replacement instructions for the proper installation of the replacement cover.

Application

Wall luminaire · Indoor luminaire with velvet white metal housing.
Luminaire with light source shielded to the front and metallic inside color of the reflection surface.
Radial light emission 360°.

Wall luminaire “STUDIO LINE”
Aluminium luminaire housing, finish Colour velvet white inside hue matt copper
Synthetic cover, translucent white 2 mounting holes ø 4.5mm
Distance apart 190mm 1 cable entry for through-wiring for mains cable
Connecting terminals 2.5@
Earth conductor terminal
2-pole connecting terminal for digital control
LED power supply unit 220-240 V x 0/50-60 Hz
DC 196-250 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
c – Conformity mark
Weight: 4.5 kg
This product contains light sources of energy efficiency classes D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

50 910.6K3

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove the mounting plate with the LED unit from its packaging.
Loosen the knurled screw (slotted) and remove the ring made of synthetic material from the LED unit.
Pass the power connecting cable through the cable entry in the mounting plate.
Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
Establish the earth conductor connection on the earthing screw (1) of the mounting plate.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, and DA are provided for digital control purposes.
If these terminals are not assigned, the luminaire will work with full light output.
Insert the ring made of synthetic material back into the LED unit and tighten the knurled screw (slotted).
Unpack the luminaire housing and carefully guide it over the LED unit.
Position and align the luminaire housing on the mounting plate and tighten the locking screw on the side.

Cleaning · Maintenance

Replacing the LED module

Replacing the power supply unit
The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
Disconnect the system from the power supply.
Loosen the locking screw on the side and lift the luminaire housing off the mounting plate.
Loosen the knurled screw (slotted) and remove the ring made of synthetic material from the LED unit.
Disconnect the earth conductor connection and the electrical connection to the terminal.
Loosen the mounting screws of the power supply unit, the round blank bracket, and earthing screws (Torx).
Remove the pot with an LED module. Install the replacement pot.
Please follow the installation instructions for the LED module.
Replace defective LED power supply unit.
Install in reverse order.