BEGA 51198.4 Indoor Illuminated Mirror Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

Product description
Overvoltage protection
Safety
Lamp
Installation
Cleaning Maintenance
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

51 198.4
Illuminated mirror for indoor use Instructions for use

Product description

Luminaire housing made of aluminium, surface Colour velvet white inside hue matt brass
Inside synthetic cover, translucent white
Mirror made of crystal glass, diameter 550 mm, visible edge polished
4 mounting holes ø 6 mm
Distance 350 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@
Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
– Conformity mark
Weight: 10.3 kg
This product contains light sources of energy efficiency class(es) D

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage	53.1 W
Luminaire connected wattage	59 W
Rated temperature	ta = 25 °C
Ambient temperature	ta max = 45 °C

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove the luminaire housing (reflector) from the packaging.
Pass the power connecting cable through the cable entry into the luminaire housing.
Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials.

Note position of application of the luminaire housing “arrow down”.
Connect the earth conductor to the earthing screw (1) of the luminaire housing.
Remove the mounting plate with LED unit from its packaging.
Loosen 4 Torx screws (T 20) and remove the central service panel from the LED unit.
Loosen earth connection (plug connection) between central service panel and LED unit.
Guide wires of the power connecting cable through the rear opening into the LED unit.
Place the LED unit over the keyholes onto the four threaded bolts of the luminaire housings and turn it clockwise until it stops.

Tighten the hex nuts M5 over the keyholes.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control purposes. If these terminals are not assigned, the luminaire will work with full light output.
Establish the earth conductor connection of the LED unit to the luminaire housing (plug connector).
Make earth connection (plug connection) from the central service panel to the LED unit again. Place the central service panel back onto the LED unit and fasten using the 4 Torx screws (T20).
Remove the mirror from its packaging.
Place the rear locking bolts of the mirror fastening onto the 3 elongated recesses of the LED unit.
Turn the mirror clockwise against the resistance until the locking bolts audibly click into their final position.

Cleaning Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Defective luminaire cover must be replaced.
Close the luminaire.

Spares