BEGA 24127 Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
24127 Wall Luminaire
Wall luminaire
Instructions for use
Application
Wall luminaire with shielded light.
Light emission 2 × 15°.
Fully glare free light for lighting wall surfaces
and for interior or exterior lighting design.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Safety glass
Optical silicone lens
Light sector 2 × 15°
Mounting plate with
4 mounting holes ø 4.5 mm
Distance apart 86 x 86 mm
2 cable entries for through-wiring of mains
supply cable ø 7-12 mm,
max. 5 G 1.5@
Connecting terminal 2.5@
with plug connection
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Basic insulation is provided between the mains
and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect
temperature-sensitive components without
switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical
impacts < 1 joule
r – Safety mark
c – Conformity mark
This product contains light sources of energy
efficiency class(es) D, E
Overvoltage protection
The electronic components installed in the
luminaire are protected against overvoltage in
accordance with DIN EN 61547.
To achieve an additional protection against
e. g. transients, etc. we recommend separate
overvoltage protection components.
You can find them on our website at
www.bega.com.
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
Safety
The installation and operation of this luminaire
are subject to national safety regulations.
Installation and commissioning may only be
carried out by a qualified electrician.
The manufacturer accepts no liability for
damage caused by improper use or installation.
If subsequent modifications are made to
the luminaire, the person responsible for
these modifications shall be considered the
manufacturer.
Lamp
Module connected wattage 4 W
Luminaire connected wattage 5.6 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 60 °C
24 127 K3
Module designation
2x LED-0886/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 580 lm
Luminaire luminous flux 175 lm
Luminaire luminous efficiency 31,3 lm / W
24 127 K4
Module designation
2x LED-0886/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 620 lm
Luminaire luminous flux 187 lm
Luminaire luminous efficiency 33,4 lm / W
Installation
Undo hexagon socket head screw (wrench
size 3 mm) through the opening in the luminaire
housing up to the stop and lift luminaire top.
Lead the mains supply cable through the cable
entry of the luminaire base.
Fix luminaire base with enclosed fixing screws
diagonally on the mounting surface.
Make the earth conductor connection and the
electrical connection.
For digital control please use the connecting
terminal DA, DA.
In case this terminal is not used the luminaire
will be operated at full light output.
In order to guarantee the maximum service
life of the electrical components, the enclosed
desiccant pouch must be placed in the
luminaire.
Remove the desiccant pouch from the foil
packaging and place it in the position marked
by the red information label immediately before
finally closing the luminaire.
Push plug into coupler as far as it will go.
Make sure that gasket is positioned correctly.
Install the luminaire top, press-on and
tighten screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free
cleansers from dirt and deposits.
Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the
luminaire housing.
It is needed to remove residual moisture.
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
Replacing the LED module
The designation of the LED module is noted on
a label in the luminaire.
The light colour and light output of BEGA
replacement modules correspond to those of
the modules originally fitted.
The module can be replaced by qualified
persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the
LED module.
Inspect and, if necessary, replace the luminaire
gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
LED power supply unit DEV-0332/350
LED module 3000 K LED-0886/830
LED module 4000 K LED-0886/840
Gasket wall box 83 000 877
Gasket housing 83 000 885
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>