BEGA 23253.3 Wall Luminaire for Indoor Use Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 23253.3 Wall Luminaire for Indoor Use
Instructions for use
DIMENSION
Product Description
Safety
FEATURES
Insulation housing
Installation
Cleaning Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 23253.3 Wall Luminaire for Indoor Use

Instructions for use

Application

Wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

DIMENSION

$BEGA-23253-3-Wall-Luminaire-for-Indoor-Use-FIG- $1$$

Product Description

Luminaire made of Aluminium, finish Chrome
Hand-blown opal glass
2 elongated fixing holes
Width 6 mm · 365 mm spacing
Insulating housing with cable entry for mains supply cable up to ø 10,5 mm, max. 3 x 1,5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-276 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
Impact strength IK02
Protection against mechanical impacts < 0.2 joule
Safety mark
Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

FEATURES

Lamp

Module connected wattage 10.5 W
Luminaire connected wattage 12.8 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C

23 253.3 K3

Module designation
LED-0424/930 LED-0425/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 1735 lm
Luminaire luminous flux 1318 lm
Luminaire luminous efficiency 103 lm / W

Insulation housing

Installation

For mounting and dismantling please keep a minimum distance of 300 mm between the removable cap and the wall.
LEDs are high-quality electronic components!Please avoid touching the light output opening of the LED directly during installation or relamping.

Open luminaire:

Loosen knob, remove cap and glass.
Drill mounting holes into the mounting surface – spacing 365 mm.
For the mains supply connecting open the insulation housing – pull open – strip mains supply cable max. 15 mm and lead it into the insulation housing – see sketch.
Make earth conductor connection and electrical connection.
Connect both parts of the insulation housing until they audibly engage.
The outer coating of the cable has to be fully enclosed by the compression nipple.
Fix luminaire with enclosed or any other suitable fixing material onto the mounting surface. Place glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.

Cleaning Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Loosen lateral knob, remove cap and take out glass.
Please follow the installation instructions for the LED module.
Defective glass must be replaced.
Insert glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.