VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR Installation Guide

October 30, 2023
VEKOOTO

VEKOOTO logo Operating Instructions & Installation GuideVEKOOTO N72 Backup
Camera with 7 Inch Monitor and DVR N72
Backup Camera with 7”Monitor and DVR
Before Operating This Set
Please Read These Instructions Completely
USER MANUAL
Thank You for Buying VEKOOTO Product.
Read This User Manual Before Installing and Using It.
Pls keep this instruction or write down our email Vekooto@outlook.com
So you can find us once you have any question.
You are Always the First for us.

Monitor introduction

The user can perform the manipulation of the guest power segment on the display parameters through the following nuclear health operations.VEKOOTO
N72 Backup Camera with 7 Inch Monitor and DVR - overview

  1. IR: Infrared connector
  2. POWER: Turn the monitor on or off
  3. +: Increase button
  4. -: Decrease button
  5. CH-: Switch channel
  6. MENU: Setting menu
  7. SEL: Confirm button

Remote Controller introduction

  1. Standby: Power ON/OFF

  2. Video Select: Channel switch
    VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Remote
Controller

  3. Menu: Go in setting page

  4. Mode Select: Show reversing line

  5. Function Down: Reduce when in setting page

  6. Function Up: Increase when in setting page Note: Button cell model: CR2025 3V

Wiring instructions  **

**

VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Wiring
instructions

The wiring method when product use, as follows:

  1. Connect Yellow wire to positive power( 12-35V)

  2. Connect Red wire to ACC
    The red wire is connected to the car ignition wire ACC switch (which is the gear switch before starting up the car’s motor), when the car key is turned on, the device will start automatically, and if the vehicle key is turned off, it will automatically turn off.

  3. Connect Black wire to negative power / Ground / Sheet Metal

  4. Connect Green wire(CH2 trigger) to reversing light

The wiring method when product test, as follows:

  1. Connect Yellow wire and red wire together to the positive power(12-35V)
  2. Connect Black wire to Ground
  3. Ignore color trigger wires
  • Before installing it by professional person, please test it if works well, like image display, just in case and save your precious time. Please contact us if you have any question anytime, our email is Vekooto@outlook.com
    Note:

    1. Before connecting, you need to confirm that the voltage of the battery is between 12 – 35V.
    2. After connecting the wires, pay attention to the insulation between the power cables to prevent. the power cables from short-circuiting the battery.
    3. The yellow wire must be connected to the ignition wire, otherwise the device will not support the ignition switch.
    4. When you install the 4pin cable, please target every pin to the hole, avoid breaking the pin.

About Trailer installation

If you need to extend the cable for your trailer, please tell us via our email: VEKOOTO@OUTLOOK.COM
So we can send the extend cable for you, then you can extend it as the attached picture below shows, and you can disconnect them by Rotating the button of cable. And please tell us how much cable you need and how many feet you need. Email us your Amazon Order ID# :
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Wiring instructions
1

How to install the monitor and camera:

  1. Install the monitor and camera
    VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR -
parts

  2. Choose the monitor brackets
    VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - parts
1

  3. Install the camera
    VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - parts
2

Basic Function **

**

Make sure Turn off the recording video function when you use the menu button into basic function. Press the SEL button of monitor let the red point disappear then the recording video function will disappear.
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Basic Function
1 7.1 Date Setting
Press the button Date Setting (Increase time/ decrease time) ■0. MODE (into next time setting) ■■ until last complete set
7.2 View
Press the button Press View
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Basic Function
2 7.3 Playback
Press the button Press twice Playback
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Basic Function
3 7.4 Split Setting
Press the button Press thrice Split Setting
Choose a default split screen mode among SIX split screen modes in picture.
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Basic Function
4 7.5 System
Press the button Press four times System
VEKOOTO N72 Backup Camera with 7 Inch Monitor and DVR - Basic Function
5

  1. Reversing Lines: off / MODE 1/2/3

  2. Astern Delay: off / 3s/ 6s/ 9s
    That means after reversing trigger ended, it will return to monitoring page after the setting time.

  3. Cyclic Record: Recording video for the certain length.

  4. Image Mirror: Normal / Mirror.
    Front/ Back each represent the camera’s image of CM1/CM2

  5. Format: format the SD card content

MENU FAQ

  1. How to return interface while viewing the file?
    A. Press the CH- button, then it can back to the monitor page.
    At other time, press the Menu button to go back the monitor page.

  2. How to rotating the image?
    A. Menu-System-Setting “Rotate” or “Image Mirror”.

  3. How to record video?
    A. Press the “SEL” button, then the red point will come that means the monitor recording.

  4. Why monitor can’t use the menu and switch channel?
    A. Please make sure that monitor doesn’t stays on recording status when you want to use other function.

  5. What is the function of Trigger wire?
    A. If you connect the trigger line to the reversing light, the screen will automatically switch to the camera that connected to the reversing light when you reverse. You don’t need to manually switch to the camera channel.

  6. How to find the Micro SD card video on the computer?
    A: Plug and play. Using a card reader that can read Micro SD card then plug it to your computer. (If you want to take out the Micro SD card, you need to unscrew the screw on the back of the upper left corner of the monitor, remove the casing, and press to eject the Micro SD card.)

  7. How to solve the problem of “no signal/ black screen”?
    A. Make sure the camera system can get the power 12-35 V.
    Check the camera that if get power?
    Please check the wire connection and sure it’s tight and right, especially the power cable. Check the pins of the cable of the monitor and 4 pins cable of the camera.
    If awkward, broken, aligned. Contact us in time, we will help you solve it.

VEKOOTO logo Email:VEKOOTO@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals