allen roth 54795 Cordless Top-Down Bottom-Up Blackout Shade Instruction Manual
- June 9, 2024
- Allen+Roth
Table of Contents
allen roth 54795 Cordless Top-Down Bottom-Up Blackout Shade
PACKAGE CONTENTS
HARDWARE CONTENTS
SAFETY INFORMATION
- Please read and understand this entire manual before attempting to assemble, operate or install the product.
PREPARATION
Before beginning installation of product, make sure all parts are present.
Compare parts with package contents list and hardware contents list. If any
part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Measuring tape, drill with 3/32
in. bit and pencil.
ASSEMBLY INSTRUCTIONS
-
How to measure and mount brackets
Lay closed shade on a flat surface. Measure the top of the shade head rail (A) 7 inches from the left side and mark with a pencil. Also measure the top of the shade head rail 7 inches from the right side and mark with a pencil. These marks will be your mounting bracket (AA) locations. Adjust the marks as needed, so the mounting brackets (AA) do not interfere with the working mechanisms within the head rail (A).
Note: Shades over 50-in will require a center bracket. For over 50-in shades, measure from left pencil mark to right pencil mark and place a pencil mark at the center location. Adjust the position as needed, so the mounting bracket (AA) does not interfere with the working mechanisms within the head rail (A).- a. For outside mounting, clip the mounting bracket (AA) onto the headrail of shade (A). Hold shade (A) level at the height desired and center it over the window opening. Mark the exact location of each mounting bracket (AA) with a pencil. Remove the mounting brackets (AA) from the headrail of shade (A). Pre-drill the screw holes and then mounting bracket (AA) to the wall or window molding with wood screws (CC).
- b. For inside mounting, clip the mounting brackets (AA) onto the headrail of shade (A). Hold shade (A) in place and make pencil mark at the rear of each mounting bracket (AA). Remove the mounting brackets (AA) from the headrail. Pre-drill the screw holes and then secure the mounting bracket (AA) to the wall or window molding with wood screws (CC).
-
Lift the blind (A) head rail into position, such that the inner front edge of the head rail slides into the slot at the front of each mounting bracket (AA). Push the head rail upward until the flexible tab at the bottom of each mounting bracket (AA) snaps onto the back of the headrail. Check carefully to ensure the head rail is properly snapped into place.
-
Attach the handles (BB) to the center of the bottom rail and middle rail of shade (A). Check carefully to assure that the handles (BB) are properly snapped into place.
-
OPTIONAL: To remove the 4 shade (A) from the mounting brackets (AA) after installation lift up the bottom of the shade (A) to gain access to the flexible tab on the bottom of the mounting brackets (AA). Use a screwdriver (Not Included) to press in the flexible tab until the shade loosens. Repeat for all mounting brackets (AA).
OPERATING INSTRUCTIONS
- Raise or lower the shade (A) by gripping the bottom rail handle (BB) and lifting or lowering the bottom rail to the desired height.
- Shade (A) can lower down 30% from the top to let light in, while still retaining privacy. Raise or lower the middle rail by gripping the middle rail handle (BB) and lifting or lowering the middle rail to the desired height.
CARE AND MAINTENANCE
The vinyl headrail and bottom rail can be wiped clean with a damp sponge. To clean the shade fabric, use a feather duster or vacuum lightly using the soft brush attachment.
ONE-YEAR LIMITED WARRANTY
For a period of one (1) year from the date of purchase, the manufacturer will replace this window covering with one of equal value if this window covering is found to be defective in material or workmanship. This warranty does not cover damage or defects caused by or resulting from improper maintenance, negligent or improper use, abuse, neglect, accidents, act of God, alteration, commercial use, installation, removal or reinstallation. This warranty is restricted to normal consumer use within the United States and Canada. To obtain warranty service, contact our customer service department at 866-439-9800. 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.
REPLACEMENT PARTS LIST
For replacement parts, call customer service 866-439-9800. 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.
- PART DD
- DESCRIPTION
- Hardware Box
- Contents AA x2, BB x2, CC x4)
- PART #/N° 79074-6SC4Z000HW2LA
Questions?
Call customer service at 866-439-9800, 8 a.m. – 8 p.m., EST. Monday – Sunday. You could also contact us at partsplus@lowes.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>