BEGA 50467.5 Ceiling Luminaire Instruction Manual

BEGA 50467.5 Ceiling Luminaire

Product Information

The product is a luminaire that requires installation and operation in accordance with national safety regulations. It is recommended to have a qualified electrician carry out the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. The luminaire is equipped with electronic components that are protected against overvoltage according to DIN EN 61547. Additional overvoltage protection components are recommended for further protection against transients.

The product features LED modules with a connected wattage of 8.1 W and a luminaire-connected wattage of 9.8 W. The rated temperature is 25 °C and the maximum ambient temperature is 30 °C. The module designation is LED-0800/930 with a color temperature of 3000 K. The color rendering index (CRI) is greater than 90. The module luminous flux is 1255 lm and the luminaire luminous flux is 1084 lm. The luminaire has a luminous efficiency of 110.6 lm/W.

Product Usage Instructions

1. Installation:
   • LED modules are sensitive electronic components, so avoid touching the light output opening directly during installation or relamping.
   • Ensure a secure connection by positioning the luminaire housing precisely in relation to the mounting plate.
   • Make sure the vertical bar inside the luminaire housing aligns with the mounting hole on the long bar of the mounting plate.
   • Press the luminaire housing firmly against the mounting plate and turn it clockwise until it reaches the stop.
   • Screw the enclosed trim ring with the attached reflector into the luminaire housing by turning it clockwise.
2. Replacing the LED module:
   • Disconnect the electrical installation before starting the replacement process.
   • Open the luminaire following the provided instructions.
   • Locate the label inside the luminaire that indicates the designation of the LED module.
   • Ensure that the replacement LED module has the same light color and light output as the original module.
   • Qualified individuals can use standard tools to replace the module.
   • After replacing the module, close the luminaire.

Spares

The following spare parts are available for this product:

• Glass/Trim ring: Part number 20 000 086 M
• LED power supply unit: Part number DEV-0409/250
• LED module 3000 K: Part number LED-0800/930
• Reflector unit: Part number 75 004 588

Dimension

Application

• Ceiling luminaire downlight · indoor luminaire with symmetrical wide beam light distribution.
• With BEGA Hybrid Optics® : Highly efficient and low-loss light distribution, thanks to reflector and optical lens.

Product Description

• Ceiling luminaire downlight »GENIUS« Die-cast aluminium housing, Colour velvet black finish
• Trim ring · Chrome finish
• Clear safety glass
• Optical silicone lens · BEGA Hybrid Optics®
• Reflector surface made of pure aluminium 2 mounting holes ø 4.5 mm
• Distance apart 96 mm
• Connecting terminals 2.5@
• Earth conductor connection
• LED power supply unit: 220-240 V 0/50-60 Hz
• DC 176-280 V
• DALI-controllable
• Basic insulation is provided between the mains and control cables
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
• Impact strength IK07
• Protection against mechanical impacts < 2 joule
• Safety mark
• CE: Conformity mark
• Weight: 0.95 kg
• This product contains light sources of energy efficiency class(es) E

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Specifications

Lamp

• Module connected wattage: 8.1 W
• Luminaire connected wattage: 9.8 W
• Rated temperature: ta = 25 °C
• Ambient temperature: ta max = 30 °C

50 467.5 K3

• Module designation: LED-0800/930
• Colour temperature: 3000 K
• Colour rendering index: CRI > 90
• Module luminous flux: 1255 lm
• Luminaire luminous flux: 1084 lm
• Luminaire luminous efficiency: 110,6 lm / W

Lighting technology

• Half beam angle 36°

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Remove mounting plate from the luminaire housing.
• Unplug the earth conductor connection (plug contact).

Please note

• If the luminaire is to be mounted onto a metallic, electroconductive surface, it is mandatory to make sure that the mounting surface is connected conductive to the earth conductor of the luminaire!
• Lead the power connecting cable through the mounting plate.
• Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
• Establish the earth conductor connection on the earthing screw (1) of the mounting plate.
• Establish the earth conductor connection to the luminaire housing (plug contact).
• Push silicone sleeves over the lines and establish the electrical connection to the terminals marked (L) and (N).
• The two connecting terminals marked DA, DA are provided for digital control purposes.
• If these terminals are not assigned, the luminaire will work with full light output.

IMPORTANT

• To ensure secure connection, the luminaire housing must be positioned precisely in relation to the mounting plate.
• Make sure that the vertical bar inside the luminaire housing is positioned precisely in the area of the mounting hole on the long bar of the mounting plate.
• Press the luminaire housing firmly against the mounting plate and turn it clockwise firmly against the stop.
• Screw enclosed trim ring with attached reflector into the luminaire housing by turning it clockwise.

Maintenance

Cleaning /Maintenance

• Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the electrical installation.
• Open the luminaire.
• Please follow the installation instructions for the
• LED module.
• Close the luminaire.

Spares

• Glass/Trim ring: 20 000 086 M
• LED power supply unit: DEV-0409/250
• LED module 3000 K: LED-0800/930
• Reflector unit: 75 004 588

BEGA Gantenbrink-Leuchten KG

• Postfach 31 60 · 58689 Menden
• info@bega.com
• www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>