BEGA 33 535 Ceiling and Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
13.18 · Technical amendments reserved
33 535
Ceiling and wall luminaire
IP 65
Instructions for use
Application
Ceiling and wall luminaire with high protection class for a variety of
lighting tasks.
A luminaire made of aluminium alloy and crystal glass.
Lamp
Module connected wattage 4.7 W
Luminaire connected wattage 5.8 W
Rated temperature ta=25 °C
Ambient temperature ta max=45 °C
33 535K3
Module designation LED-0338/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 975 lm
Luminaire luminous flux 609 lm
Luminaire luminous efficiency 105 lm/W
33 535K4
Module designation LED-0338/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 1005 lm
Luminaire luminous flux 627 lm
Luminaire luminous efficiency 108,1 lm/W
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Product description Luminaire made of aluminium alloy, aluminium and stainless
steel
BEGA Unidure® coating technology
Crystal glass with white matt finish
Silicone gasket
2 mounting holes ø 4.5 mm
Distance apart 150 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connecting terminal 2.5 with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
– Safety mark
– Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency classes B
Installation
Undo locking screw and turn cover ring as far as it will go.
Remove cover ring and glass from the luminaire base.
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Disassemble LED module.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
It is absolutely essential to use the enclosed ring gaskets.
Make earth conductor connection.
Make electrical connection.
Assemble LED module.
Make sure that gasket is positioned correctly.
Place cover ring with glass onto the luminaire base and turn it clockwise as
far as it will go. Tighten locking screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass 11 002 864 11
LED power supply unit DEV-0303/350
LED module 3000 K LED-0338/830
LED module 4000 K LED-0338/840
Gasket 83 001 313
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com