Ningbo CM-DRC Electric Winch Wireless Controller Instructions

Ningbo CM-DRC Electric Winch Wireless Controller

Product Information

Specifications

• Firing Frequency: 315MHz
• Control Range: More than 20 meters

Features Overview
The Electric Winch Wireless Controller is designed to provide wireless control for electric winches. It operates at a firing frequency of 315MHz and has a control range of more than 20 meters.

Product Usage Instructions

Step 1: Installation
Before using the wireless controller, it needs to be installed properly. Follow the steps below:

1. Locate the control box of your electric winch.
2. Identify the wires for the wireless controller.
3. Connect the wires of the wireless controller to the corresponding terminals on the control box.
4. Ensure all connections are secure and properly insulated.

Step 2: Pairing the Wireless Controller
Once the installation is complete, you need to pair the wireless controller with the electric winch. Follow these instructions:

1. Ensure both the wireless controller and the electric winch are powered on.
2. Press and hold the pairing button on the wireless controller for 5 seconds.
3. Observe the LED indicator on the controller. It should start blinking rapidly.
4. Within 10 seconds, press and release the pairing button on the electric winch.
5. The LED indicator on the wireless controller should stop blinking and remain solid, indicating a successful pairing.

Step 3: Operating the Electric Winch
Now that the wireless controller is paired with the electric winch, you can use it to operate the winch. Follow these instructions:

1. Hold the wireless controller in your hand.
2. Ensure you are within the control range of more than 20 meters.
3. Press the desired control buttons on the wireless controller to activate the winch. The specific buttons and their functions may vary depending on the winch model.
4. Release the buttons to stop the winch.

FAQ

• Q: What is the firing frequency of the wireless controller?
  A: The firing frequency of the wireless controller is 315MHz.

• Q: What is the control range of the wireless controller?
  A: The control range of the wireless controller is more than 20 meters.

• Q: How do I pair the wireless controller with the electric winch?
  A: To pair the wireless controller, ensure both devices are powered on, press and hold the pairing button on the wireless controller for 5 seconds, observe the LED indicator, and press the pairing button on the electric winch within 10 seconds.

Electric winch wireless controller instructions

Features Overview
This wireless remote control firing frequency of 315MHz, the control range of more than 20 meters, used in electric winch wireless control.

The wireless remote control parameters

1. Working voltage: DC3V, 2 pcs CR2032 battery.
2. The working current: 35mA ± 5mA
3. Transmitting frequency: 315MHz
4. The transmit power: <10dBm
5. Standby current: <5uA

Using

The remote controller have 3 keys. Press and hold the ”ON/OFF” button more than 3 seconds, the remote powered on, while the LED indicator lights. Then press the key of  “OUT” or “IN”, it will trigger 315 MHz high frequency FSK modulation unit to transmit the  address code and key value. The high- frequency signal emitted by the antenna. When the  remote control has been powered on, press and hold the ”ON/OFF” button more than 3 seconds, the remote control is turned off, while LED is off. If there is no key operation within 50 seconds, it will automatically shut down.

Installation and function

1. Disconnect Power to the winch

2. Confirm that the plug is the correct type for this winch and plug it in

3. Select an area for the receiver on the vehicle close enough to the winch to allow cable connection

4. Investigate the chosen area to make sure no components will be damaged by installation.

5. Permanently (optional) mount the remote control receiver to the vehicle using appropriate hardware (not included).

6. Preare the winch for operation as explained in its manual

7. Reconnect winch’s power

8. Release the clutch handle and pull out about 10 feet of wire rope Leave the wire rope laying on the ground and stay clear of the wire rope and hook

9. Reengage the clutch handle

10. Watch the spool and wire rope and briefly, press the “OUT” button on the remote control to verify that the cable feeds out
    WARNING! If the cable does not feed out check and correct the winch’s wiring. Retest after correction.

11. Watch the spool and wire rope and briefly press the “IN” button on the remote control to verify that the cable retracts
    WARNING! If the cable does not feed out check and correct the winch’s wiring Retest BOTH functions after correction.

12. If the remote operates the winch properly, it is ready for use.

13. After use, disconnect control box from winch to prevent accidental operation

Wiring diagram

WARNING!

To prevent serious injury

1. Disconnect control box from winch before service and after every use.
   WINCH CAN OPERATE SUDDENLY AT ANY TIME WHILE CONNECTED.

2. Stand clear of winch, fairlead, and wire rope while connected. Keep bystanders away.

3. Only operate controls when winch and entire wire rope is within view.

4. Use with vehicle mounted recovery winches only. Do not use for any other application.

5. Confirm control box mounting location has no wire or components that can be damaged drilling.

6. Read winch manual before use.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuan t to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterferenc e to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or reloca te the receiving antenna.
• Increase the separation between the equi pment and receiver.
• Connect the equipment into an outlet on a circuit different f rom that to which the receiver is c onnected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference r eceived, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>