THE DRIVESHAFT SHOP 2015 plus SRT8 Hellcat One Piece Driveshaft Owner’s Manual
- July 5, 2024
- THE DRIVESHAFT SHOP
Table of Contents
THE DRIVESHAFT SHOP 2015 plus SRT8 Hellcat One Piece Driveshaft
Our driveshafts have been designed with the highest quality standards in mind for maximum performance. We have manufactured and precision-balanced each shaft to allow your vehicle to transfer more power to the ground. This driveshaft is intended for high-performance applications where vehicle performance and safety are top priorities. Please note that you are converting from an OE two-piece driveshaft design to an aftermarket High-Performance one- piece design. With this change and other performance driveline & suspension components that need to be installed in tandem will impact overall NVH (Noise, Vibration, Harshness) during certain operating conditions. To minimize the effects of NVH we recommend you start by rotating the driveshaft 180 degrees and bolting your driveshaft into its new position. To find the optimal operating position it is possible that you will need to make small adjustments and evaluate performance during this process. For more information on this refer to our Vibration Checklist located in the support section of our website.
Product Specifications
- Product Name: 2015+ SRT8/HELLCAT Aluminum and Carbon One-Piece Driveshaft
- Design: High-Performance One-Piece Design
- Application: High-performance vehicles
- Material: Aluminum and Carbon
- CV Clearance Requirements:
- CHARGER SRT8/HELLCAT AUTOMATIC – 3.25-3.75
- CHARGER SRT8/HELLCAT MANUAL – 5.25-5.75
- Adapter Plate Hardware Torque: (4) M12 Bolts 70 ft-lbs / (20) M10 Bolts 57 ft-lbs
- Exhaust System Modification : May require modification for .75 inches of clearance
Product Usage Instructions
EXTREMELY IMPORTANT: NOT CHECKING MEASUREMENTS WILL VOID THE WARRANTY
- Conversion Process: Ensure you are converting from an OE two-piece driveshaft design to the aftermarket one-piece design.
- Installation:
- Rotate the driveshaft 180 degrees before bolting it into its new position.
- Check Driveshaft CV Clearance after installation to ensure it meets the specified dimensions.
- If necessary, make small adjustments to find the optimal operating position.
- Refer to the Vibration Checklist on the manufacturer’s website for more information.
- Torque Specifications: Follow the recommended torque values for the adapter plate hardware.
- Exhaust System: Check and modify the exhaust system if needed to ensure adequate clearance.
Driveshaft CV Clearance MUST BE CHECKED after installation.
- If dimension is not within the allowed range, do not run the driveshaft.
- CHARGER SRT8/HELLCAT AUTOMATIC – MUST BE BETWEEN 3.25”-3.75”
- CHARGER SRT8/HELLCAT MANUAL – MUST BE BETWEEN 5.25”-5.75”
Adapter plate Hardware Torque:
- (4) M12 Bolts 70 ft-lbs / (20) M10 Bolts 57 ft-lbs
- DIFFERENTIAL AND TRANSMISSION SPACERS ARE NOT REQUIRED FOR 2015+
- PLEASE NOTE: EXHAUST SYSTEMS MAY NEED TO BE MODIFIED FOR ADEQUATE
- CLEARANCE (.75”)
Frequently Asked Questions
-
Q: What should I do if the Driveshaft CV Clearance is not within the allowed range?
A: If the CV Clearance is not within the specified range, do not run the driveshaft. Adjustments may be needed to ensure proper fit and function. -
Q: Do I need to modify my exhaust system for installation?
A: Depending on your vehicle, you may need to modify the exhaust system to provide adequate clearance for the driveshaft. Please refer to the product manual for details. -
Q: What impact will changing to a one-piece driveshaft have on NVH?
A: Changing to a one-piece driveshaft may impact Noise, Vibration, and Harshness (NVH) levels during certain operating conditions. Follow the manufacturer’s recommendations for minimizing NVH effects.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>