BEGA 50 689 Semi Recessed Downlight Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50 689 Semi Recessed Downlight
Dimension
Recessed ceiling downlight for indoor use
Application
Recessed ceiling downlight · Interior luminaire with symmetrical narrow beam
light distribution for connection to an external LED power supply unit.
For surface-mounted installation in indoor suspended ceilings of 8-25mm
thickness.
Product description
Recessed luminaire without power supply unit
Luminaire housing made of cast aluminium
Installation housing is made of glass-fibre reinforced polyamide with 2
fastening springs
Reflector made of pure anodised aluminium
Optical silicone lens
Partially matt crystal glass
Recessed opening ø 188mm
Required installation depth 125mm
1 connecting cable with strain relief and plug connector system for BEGA power
supply unit, on/off or DALI
Safety class III
– Conformity mark
Weight: 2.4 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 17.2 W
- Luminaire connected wattage 19.8 W
- Rated temperature ta=25 °C
- temperature ta max=40 °C
50 689K3
- Module designation LED-0785/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 2655 lm
- Luminaire luminous flux 1724 lm
- Luminaire luminous efficiency 87,1 lm/W
Lighting technology
Half beam angle 48
Installation
Luminaire housing must not be installed in heat-insulating material.
A separate power supply unit is required to operate the luminaire.
For connection to external LED-power supply unit – accessory 13 144 or 13 170
– the luminaire is equipped with a 2-pin connector.
Note operating instructions of the LED-power supply units.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
The recessed opening is covered by the frame of the luminaire housing.
Fixing of the installation housing in the recessed opening is achieved by
using two adjustable springs.
Installation into inserted ceilings:
A recessed opening of 188 mm is necessary to accept the installation housing.
Recessed depth min. 125 mm.
The lateral distance between recessed luminaire and other building parts must
be at least 50 mm.
Compress the fastening springs of the installation housing against their
spring pressure on both sides towards the housing and slide the installation
housing into the recessed opening.
The fastening springs catch the ceiling panel from the back side. Minimum
thickness of the ceiling panel is 8 mm. If minimum thickness of the panel is
less than 3 mm it must be reinforced from the reverse side. Maximum thickness
of the ceiling panel must be no more than 25 mm.
Push the enclosed threaded rods through the two inside openings of the
installation housing and guide the clamping angle of the threaded rods
downwards onto the suspended ceiling.
Clip the threaded rods into their guide grooves and screw them in by hand as
far as possible.
Fix in end position with screwdriver (TX 10).
This clamp fixing prevents the installation housing from turning and dropping.
Connect to the LED power supply unit. Route the LED power supply unit through
the installation housing and place it in the suspended ceiling.
Connect the 2-pin plug connector between luminaire and external LED power
supply unit.
Press together the two internal fixing sliders inside the luminaire housing.
Push the luminaire housing to the end of the installation housing and then
release the fixing sliders.
This mechanism ensures that the luminaire housing sits securely inside the
installation housing.
Installation housing and external LED=power supply unit must not be
installed in heat-insulating material.
Please use the protective gloves provided for the installation to prevent
finger prints on the reflector.
Place the reflector with silicone lens onto the glass. Twist the glass with
the attached reflector to the right to fix the assembly inside the luminaire
housing.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation
instructions for the LED module.
Close the luminaire.
Accessories
Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
13 144 Power supply unit on/off
13 170 Power supply unit DALI
The power supply units are only suitable for the operation of one LED luminaire.
For the accessories a separate instructions for use can be provided upon request.
Spares
Spare glass 11 003 456 10MRG
LED module 3000 K LED-0785/930
Reflector 75 002 753
Customer Support
4/4 BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·info@bega.com · www.bega.com
Documents / Resources
| BEGA
50 689 Semi Recessed
Downlight
[pdf] Instruction Manual
50 689 Semi Recessed Downlight, 50 689, Semi Recessed Downlight, Recessed
Downlight, Downlight
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>