inovelli 7CA-SS-VE-C0 Motion sensor Pet Immunity ZWave User Guide

Inovelli Motion sensor Pet Immunity ZWave™
7CA-SS-VE-C0
Motion Sensor Pet
immunity
Quick Start Guide

Product Introduction

The Motion Sensor lets you know when movement is detected in a certain area and can trigger different actions in response to that movement (or lack of movement). It supports pet immunity up to 80 lbs. This sensor integrated a Z-Wave communication module to connect with the Z-Wave gateway, and this device can be adapted to EU(868.42Mhz) or US(908.42MHz).
If you want your Motion Sensor to be a security device that uses secure/encrypted message to communicate in a Z-Wave network, then a security- enabled Z-Wave controller is needed.
The motion sensor can be included and operated in any Z-Wave network with other ZWave certified devices from other manufacturers and/or other applications. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.

2. Product Appearance
Product appearance and function overview.

Button:

• Short press the reset button into learning mode, then the sensor can inclusion or exclusion from the Z-Wave network.
•  Hold the key for 5s to reset the sensor, after reset, the Sensor will send “Device_Reset_Locally” to the main controller and exclude it from the Z-Wave network when the Button is released, this procedure will reset the Sensor to factory default.
•  Short press the button for 3 times then the sensor sends wake up notification on to gateway, and LED will fast blink when sending data, send over then the L  ED turn off..

Specification

Detection angle| 80 degrees
Detection distance| 8 meters / 26.25 feet
Pet immune| 80 lbs (36 kgs)
---|---
Mounting     height| 6.23 ft. to 7.55 ft.
(1.9m to 2.3m)
Light sensor| 20 lux for day/night(bright/dark)
Protocol| Z-Wave
Frequency| 908.42MHz (US)
868.42MHz(EU)
Power source| Battery-powered
Battery type| CR123A X 1
Battery life| 3 years
Anti-Tamper| YES
Low power alarm| YES
Certifications| CE/FCC/Z-Wave

Features/Capabilities:

•  Supports pet immunity up to 80 lbs (36 kgs)
•  Use PIR & Fresnel lens technology
•  Easy installation with bracket
•  Low battery alarm
•  Equipped with an anti-tamper switch that reports any tampering

 Installation Position and Notes

1. Installation position should be chosen at the area which the bass-by will be across, try to make the bass-by in the detection area as below.
   Side view

2. Do avoid installation near air-conditioner, electric fans, refrigerators, ovens or other places where temperature easy change.

3. In order not to affect the detecting result, there should be no object in front of the produced lens.

4. Building (such as the wall) will shorten the distance of wireless communication.

5. This device can be mounted on the wall only, it cannot be installed on the ceiling.

5. Product Installation
Adding the device as accessories, install it according to the diagram below:

1. Choose the installation location on the wall, fix the bracket by screw or 3M adhesion tape on the wall.
2. Take off the bracket in the back, and draw out the battery insulation sheet, then assemble the bracket.
3. Assembly the main body to the bracket.

Product Usage

The function of Action Button:
6.1 All functions of each trigger:
Function Of Action

Power on

| In the network: Send Battery report and Wake up a notification, the LED

turn on within 1 second.

Not in the network: Only the LED will be slow blink 3 times.

SmartStart Inclusion

| Add the Motion Sensor into the Z-Wave network via SmartStart:

1. Add your Motion Sensor device to the primary controller’s SmartStart provisioning list (if you don’t know how to do this, refer to its manual) by scanning your device’s QR code

2. Power on the motion sensor again.

3. The motion will send the “Z-Wave protocol Command Class” frame to start SmartStart Inclusion.

4. Led will fast blink and solid for 2 seconds to indicate the inclusion is

successful, if inclusion failed, Led will off.

Short press the button three-time| Add the Motion Sensor into the Z-Wave network:

5. Power on your Motion Sensor, and let your Z-Wave controller into add/inclusion mode.

6. 3 consecutive clicks in 1.5 seconds, the Motion Sensor will send out a node info security CC in the command class list (Security inclusion), the LED will be fast blink for 30 seconds.

7. If the inclusion is successful, the LED will be turned on within 2 seconds. If failed, LED will be turned off forever, and please repeat the steps in above.

Remove Motion Sensor from a Z-Wave network:

1. Power on your Motion Sensor, and let the Z-Wave primary controller into remove mode.

2. 3 consecutive clicks in 1.5 seconds, the LED will be fast blink for 30 seconds.

3 If Motion Sensor has been successfully removed from your Z-Wave

network, the LED will be turned on 2 seconds. If failed, LED will be turned off forever, and please repeat the steps in above.

** Short press the button one time| In the network: Send Wake up a notification, and the LED will fast blink when sending data, send over then the LED turn off.
---|---
Not In the network: NOP.
Press and hold more than 5 seconds| Reset Motion Sensor to factory default. **

1. Triggering this action, in 5 seconds LED will accelerate blink. After 5 seconds, the LED will remain on until the key is released. Motion Sensor will send “Device_Reset_Locally” to the main controller and exclude it from the Z-Wave network when the button is released, this procedure will reset the sensor to factory default.
2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
3. When not in the network, triggering this action, in 5 seconds LED will accelerate blink red. After 5 seconds, the LED will remain on red until the key is released. this procedure will reset the sensor to factory default.

** Motion is triggered| In the network: Send Notification report and Sensor multilevel report and Basic set (Setup configuration parameter 0x0E to 0x01), and the LED will be turned on for 0.2 seconds.
Not in the network: The motion sensor is disabled.
Tamper switch is triggered| In the network: Send a Notification report, and the LED will be turned on 0.2 seconds.
Not in the network:** Tamper switch is disabled.

6.2 Caution:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Hereby, Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU

6.3 Low voltage alarm to remind changing the battery.
This product has low voltage detection reminder, when the battery voltage is in low status, the detector will give out a low battery signal to the controller.

 Attention

1. If need to clean the sensor, please use a soft cloth with a little alcohol to wipe it after you cut off the power.
2. This product is just for indoor use.
3. Replace the battery timely on low battery warning to ensure the detector works properly. Please remove the battery and safekeeping, if you don’t use this product for a long time.
4. This device can be mounted on the wall only, it cannot be installed on the ceiling.
5. The reference range template of PIR detection is tested at the indoor temperature (the range is 20℃～25℃)， the target of the test is 77kg±10kg weight and 1.71m±0.3m height, the target of the test across movement speed is 4m/s±0.15m/s.
6. In order to prevent the PIR sensor’s abnormal fault, please don’t mount and operate the sensor in the below conditions,
   Firstly, product mounting should prevent being installed in the airflow environment such as in front of the door, window, heater, air conditioner, and so on.
   Secondly, the PIR detection area should not be shielded by another screen.
   Thirdly, if the operating temperature range is out of the defined range of product specification may result in some product faults, which is not in the technique commitment of the manufacturer.
   Fourthly, this product has mot pet immunity function, so when some animals go through in front of the product may trigger PIR function reported.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Dispose of the device separately from household waste at an official collection point Professional recycling protects people and the environment against potential negative effects

Command Class List

| Non-Included Non-Secure| Included SO Non-Secure
---|---|---
Node Info Frame| COMMA,. 0 _CLASS_ZWAVEPLUS_INFO COMMAND _CLASS_ASSOCIAT ION
COMMAND _CLASS_ASSOCIAT ION_ORP_NFO CO MMANOSLASS_TRANSPORT_SERVICE_V2 COMMAND_CLASS VERSION COINAANO_CLASSJIANUFACTURER_SPEC I F IC COMMANO_CLASS_DEVICE_RESET_LOCALLY COMWMO_CLASS_POWERLEVEL COMIMNO_CLASS_BATTF-RY COIAIMNO_CLASS_SECURTY ODIAIMNO_CLASS_SECURTY,
ODIAW010 CLASS_NOT IFICATION_V3| COMMAND  C LAS S ZNAVE Pt U S IN FO
COMMAND C LAS STRAN SPORT SERVICE _V2 COMMAND CLASS SECURITY
COMMAND _CLASS  S E C URIT Y_2
COMMAND CLASS  SUPERVISION
ODIAIMNO_CLASS_SENSORJAULT ILEVE L_V3 001AMANO_CLASS_WAXE _UP
OIDIAPMNO_CLASS_SUPE RVISION 001APMNO_CLASS_CONFIGURATION_V4 COMP•MO_CLASS_F IRIAWARE_UPIDATE_MO_V 7)
Securely Command
Supported Report Frame| | COMMAND_CIASS_VERSION COMMAND_CIASS_POWERL EVEL COMMAND_CIASS_ASSOCIAllON
COMMAND_CLASS_ASSOCIAllON_GRP_INFO COMMAND_CLASS_IMNUFACTURER_SPECIFIC COMMAND_CLASS_DEVICE_RESET_LOCALLY
COIANW1D_CLASS_BATTERY COMIAMO_CLASS_NOTIFIC ATION_V3 COMIAMO_CLASSWAKE-UP COMIAMO_CLASS_CONFIGURATICN_V4 COMMAND_CLASS_SENSORJAUL1TL EVE L_V5 COMMAND_CIASS_FIRMWARE_UPDATEJAD_V5
| Included S2 Non-Secure|
Node Info Frame| 00141VANO_CLASS_ZWAVEPL US_INFO °DAMAN 0 _CLASS_T RANSPORT_SERVICE COWAN 0 _CLASS_SECURITY
COWAN 0 _CLASS_SECURITY,
COWAN 0 _CLASS_SUPE RVISION|
Security
Command
Supported Report
Frame| COWAN 0 _CLASS_VERSON COWAN 0 _CLASS_POWERLEVE L COMMAND _CLASS_ASSOCIAT ION
COMIMNO_CLASS_ASSOCIAT ION_GRP_INFO COMMAND_CIASS_MANUFACTURE R_SPEC F IC OOMIVANO_CLASS_DEVCE_RESET_LOCALLY COWAN 0 _CLASS_BATTF-RY
ODNIMAN 0 C LASS_NOT IFICATION_V3
COMMENT 0 C LA SS_WAXE _UP
GORMAN 0 _C LA SS_CONFIGURATIONV4 GORMAND C LA 55 SEN SOR AWL T ILE VE L_V5 GORMAN 0 C LA SS_FIRIAVARE_UPIDATE_MO_V3|

Association Command Class
Motion Sensor supports 2 association groups and max 5 nodes for each group.
Association Group Info Command Class
Association Group Info

Association Group Command-List

Notification Commands

(0x08) MOTION_DETECTION_UNKNOWN_LOCATION

POWER_MANAGEMENT (0x08)

| (0x0A) REPLACE_BATTERY_SOON
(0x0B) REPLACE_BATTERY_NOW
(0x00) NO_EVENT

LIGHET_ALARM(0x14)

| (0x00) NO_EVENT
(0x01) LIGHETSENSOR_ALARM_DETECTED

Configuration Set Command Class Command Format

Command Class = COMMAND_CLASS_CONFIGURATION

Command = CONFIGURATION_SET

Parameter Number

Default

|

Reserved

|

Size

Configuration Value 1(MSB)

Configuration Value 2

……

Configuration Value n(LSB)

5.4.1 Parameter Number Definitions (8 bit)

Name| Info| Parameter er

Number

| Default Value| Max Value| Min Value| Size| Rea d only| Format| Altering capabilit

ies

---|---|---|---|---|---|---|---|---|---
LowBatPrecent| LowBatAlarm| 0x0A (10)| 10 (0x0A)| 50 (0x32)| 5 (0x05)| 1| NO Read-only| UNSIGNED

**** _INTEGER

| Will alters capabilities

Pironoff

| ****

PironoffSet

| ****

0x0C (12)

| ****

1 (0X01)

| ****

1 (0X01)

| ****

0 (0X00)

| ****

1

| NOTRead- only| UNSIGNED

**** _INTEGER

| Will alters capabilities

PirTimeout

| ****

PirTimeoutSet

| ****

0x0D (13)

| ****

60 (0X3C)

| 15300

( 0x3BC 4)

| 05 (0x05)| ****

2

| NO Read- only| UNSIGNED_INTEGER| Will alters capabilities
BasicEnable| SendBasic| 0x0E (14)| 0 (0X00)| 1 (0X01)| 0 (0X00)|

1

| NOTRead- only| UNSIGNED_INTEGER| Will alters capabilities
BasicReverse| BasicValue| 0x0F (15)| 0 (0X00)| 1 (0X01)| 0 (0X00)|

1

| NOTRead- only| UNSIGNED_INTEGER| Will alters capabilities
PirSensitivity| PirSensitivitySet| 0x10 (16)| 9 (0X09)| 10 (0X0A)| 0 (0X00)| 1| NORead- only| UNSIGNED_INTEGER| Will alters capabilities
**** PirPetImmunity| PirPetImmunitySet| 0x11 (17)| 0 (0X00)| 1 (0X01)| 0 (0X00)| 1| NORead- only| UNSIGNED_INTEGER| Will alters capabilities
LightSensorSend Type| LightSensorSendSet| 0x12 (18)| 1 (0X01)| 3 (0X03)| 1 (0X01)| 1| NORead- only| UNSIGNEDINTEGER| Will alters capabilities

5.4.2 Parameter Number description

value range are 5~50 for percentage, the battery’s low power level can set 5%~50%.

0x0C(12)

| Enable/Disable the PIR 0 = Disable the PIR.

1 = Enable the PIR.

---|---

0x0D (13)

| Setup the wait time of PIR for clear the motion. Valid values: 0x05~0x3BC4
0x0E (14)| When the Motion Sensor is triggered, if this parameter is 0x01 then it will send Basic set command to group 1.0 = Don’t send.1 = Send.
0x0F (15| PIR triggers the correspondence between the value of the Basic set and the PIR state-If this value is 0x00 PIR triggers send the basic set with 0xFF, PIR alarm release send the basic set with 0x00.-If this value is 0x01: PIR triggers send the basic set with 0x00, PIR alarm release send the basic set with 0xFF.Only support 0x00 and 0x01 values as a valid values.
0x10 (16)| Motion detection sensitivity level is a value between 1 and 10. This value affects the amount of motion energy required to generate a motion event and also affects the detection range and angle1 = Lowest Motion Sensitivity10 = Highest Motion Sensitivity
0x11 (17)| Enable/disable pet immunity mode. This feature is lens dependent and the detection range may be reduced when Pet Immunity is enabled.0 = Disable the pet immunity mode1 = Enable the pet immunity mode
0x12 (18)| Configure light sensor to upload data form 1=Upload lumens value.2=Upload day or night(By notification).3=Upload lumens and day/night.

5.5 Sensor_Multilevel

LARSON

Documents / Resources

| inovelli 7CA-SS-VE-C0 Motion sensor Pet Immunity ZWave [pdf] User Guide
7CA-SS-VE-C0, 7CA-SS-VE-C0 Motion sensor Pet Immunity ZWave, Motion sensor Pet Immunity ZWave
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>