Savio SIGMA X1 Professional Gaming PC Case User Manual

SIGMA X1 / SIGMA X1 WHITE
PROFESSIONAL GAMING PC CASE

USER MANUAL

SIGMA X1 Professional Gaming PC Case

LET’S PLAY 2GETHER

Thank you for choosing Savio product!
If our product meets your expectations, share your opinion with other people on the portal ceneo.pl, social media or on the website of the store where you made the purchase. If you want to show our device on SAVIO Facebook Page, we will be very pleased.
If there is something that we could improve on our products, please write to us at support@savio.net.pl
Thanks to your feedback, we will be able to better adapt the product to your expectations.

MOUNTING ACCESSORIES

SPECIFICATION

× SSD (2.5”)
I/O Ports :| 1 × USB-C 3.1 Gen 1; 1 × USB-A 3.1 Gen 1; 1 × USB-A 2.0; HD audio
Side Panel :| Tempered glass
Maximum VGA length :| 400 mm (vertical/pionowy)
Front panel :| Tempered glass
Maximum CPU cooler height :| 165 mm
Supported PSU types :| All types of standard
PCI expansion slots :| 7
Dust filter :| 1 × top/góra, 1 × bottom
Fans control by :| Motherboard/LED button
Fans included :| 3 × 120mm ARGB, PWM, 800-1800 RPM (2 × right panel/prawy panel, 1 × rear/tył)

Supported fans :

| right panel| 2 × 120 mm
rear| 1 × 120 mm
top| 3 × 120 mm or/lub 2 × 140 mm
bottom| 3 × 120 mm
Watercooling support :| rear| 1 × 120 mm
top| 1 × 120/240/280/360 mm
Product dimensions:| (L × W × H) 425 × 210 × 478 mm
---|---
Case material :| SPCC 0.7 mm
Net/gross weight :| 6.7/7.7 kg

FRONT PANEL

ASSEMBLY OF COMPONENTS

STEP 1
SIDE PANELS REMOVING

1. Remove the two screws at the back of the housing for the panel right side (metal) panel and then remove it in the direction shown in picture 1.
2. The left (glass) side panel is mounted on latches, remove the panel in the direction, remove the panel in the direction shown in picture 2.
3. Front panel (glass) is mounted on on latches, remove the panel in the direction shown in picture 3.

STEP 2

PSU INSTALLATION

Place the power supply in correct location, then secure it with screws. Pay attention the PSU fan should be facing down.

STEP 3

SSD/HDD DRIVES INSTALLATION

Insert the SSD or HDD drive in dedicated space (presented on the pictures below) and secure them with screws.

STEP 4

ATX/EPS CABLE/ KABEL ATX/EPS

Pass the ATX/EPS cable through proper holes in PC case.

STEP 5

MOTHERBOARD INSTALLATION

In case of having ATX motherboard you need to assembly additional M/B standoffs in proper places in PC case.

1. Place I/O shield in the PC case.
2. Place the motherboard on the standoffs.
3. Secure the motherboard with screws.
4. Plug the EPS and ATX cables into the proper sockets on the motherboard

STEP 6

GPU INSTALLATION

1. Uninstall the expansion card cover.
2. If necessary, remove some PCI-E slot covers.
3. Insert GPU card into PCI-E slot.
4. Secure the GPU card with screws.
5. Plug the PSU connector into the GPU socket.
6.  Install the expansion card cover.

STEP 7

I/O PANEL INSTALLATION

Top I/O panel is equipped with USB ports, audio and microphone. For its proper operation, it is required to connect the wires coming from it to the appropriate connectors on the motherboard.

ARGB BACKLIT CONTROL

PRE-ASSEMBLY INFORMATION – IMPORTANT

The kit consists of one master fan, which we can recognise from the included SATA connector, and two secondary fans. In order to correctly install the kit in the computer, the 12 V and 5 V lines must be connected in this order, so that the connectors of the master fan are connected directly to the motherboard. By default, the fans are set to control mode via the motherboard (3-pin ARGB 5 V), to switch to control mode using the RESET/LED button, go to section “backlit selection control modes”.

OPTION 1

BACKLIT CONTROL BY MOTHERBOARD

If the motherboard has a 3-pin ARGB 5 V socket, the backlight can be controlled by using a dedicated motherboard software.

1. Connect the master fan to the 3-pin ARGB 5 V and 4-pin 12 V sockets on the motherboard
2. Connect the SATA power supply for the master fan.

OPTION 2

BACKLIT CONTROL BY MANUAL MODE (LED BUTTON)

If the motherboard does not have a 3-pin ARGB 5 V connector, the backlight can be controlled using the RESET or LED button (if the computer case has a dedicated button) located on the top of the housing.

1. Connect the master fan to the 4-pin 12 V socket on the motherboard and also connect the SW lines with the LED/RESET cable from your case.
2. Connect the SATA power supply for the master fan.

ATTENTION!
If this control method is selected, after turning off the computer, the backlight colour of the fans will not be remembered and the basic colour will be restored.

BACKLIT SELECTION CONTROL MODES

If the master fan is connected at the same time to the motherboard and RESET/LED button, only one mode of backlight control will work properly. To change backlight mode control you need to:

1. Press the RESET/LED button placed on the top part of case for about 3 sec.

ADDITIONAL INFORMATION

1. The screws for additional fans are not included in the mounting set.
2. The VGA holder is not included in the mounting set.
3. Do not cover vent holes which are located at the top, rear, front and bottom of PC case.
4. Maximum possible number of fans connected to the master fan: 9 pcs

SAFETY CONDITIONS

• Use the product in accordance with its intended use, as improper use may damage the product.
• Do not expose the device to moisture, heat or sunlight, do not use the product in a dusty environment.
• The device should be cleaned only with a dry cloth.
• Independent repairs and modification result automatic loss of the warranty.
• Hitting or dropping may damage the product.

Information of the utilization of electrical and electronic equipment
This symbol indicates that electrical equipment should not be disposed of with other household waste. Used equipment should be sent to a local collection point for this type of waste or to a recycling centre. Please contact your local authorities for information about disposal methods available in your area. Waste electrical equipment may contain dangerous substances (e.g. mercury, lead, cadmium, chromium, phthalates) which can get into air, soil and groundwater when leaking from used appliances. Environmental pollution of these substances leads to their bioaccumulation, causing lesion of disease in living organisms, which would pose a risk to human and animal health or life. Households may contribute to environmental protection by proper waste collection. In such way, dangerous substances from the equipment are neutralized and valuable secondary raw materials are reused for production of new equipmentmay result in electric shock.

Warranty:

The warranty covers a period of 24 months. Independent repairs and modifications result in automatic loss of the warranty. Warranty card is also available for download on our website: www.savio.net.pl/en/service

Information for customers and contractors and communication regarding complaints:
Pursuant to Article 13 section 1 and 2 of the General Data Protection Regulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 (hereinafter referred to as GDPR), please be advised that Elmak Sp. z o.o., with its registered seat at ul. Morgowa 81; 35-323 Rzeszów becomes the Administrator of your personal data. The Specialist for General Data Protection (SODO) can be contacted in writing to: SODO, Elmak Sp. z o.o., ul. Morgowa 81; 35-323 Rzeszów, via e-mail address: sodo@elmak.pl, and by phone at +48 (17) 854 98 14. Your personal data will be processed in order to perform the contract, in accordance with Article 6(1)(b) of the afo- rementioned regulation, to the extent resulting from tax laws and financial regulations. Recipients of your per-sonal data include entities authorized by legal regulations to obtain personal data as well as processing entities providing services to Elmak Sp. z o.o. Your personal data will be stored on the basis of Administrator’s legitimate interest. You have the right to access your data, and the right to rectify, delete or limit processing of your data. You have the right to lodge a complaint to the supervisory body if you believe that the processing violates the GDPR. The provision of personal data is voluntary, however, a failure to provide such data may result in a refusal to conclude or in termination of a contract. Your personal data will not be subjected to automated decision making, including profiling referred to in Article 22 section 1 and 4 of the GDPR of April 27, 2016.

Product meets the requirements

**** Declaration of Conformityis available for download on website: www.savio.net.pl/do-pobrania

Producer:
Elmak Sp. z o.o.
ul. Morgowa 81
35-323 Rzeszow, Poland
www.savio.net.pl
FB.COM/SAVIONETPL
@SAVIO.POLSKA

References

• Strona główna - Savio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>