PERLESMITH PSTVS04 Table Top TV Stand Instruction Manual

PERLESMITH PSTVS04 Table Top TV Stand

Product Information

Product Usage Instructions

1. Step 1: Assemble the Base
2. Step 1-1: Place foot pads [W] to the frosted side of the tempered glass base [O] in the corners.

WE’RE HERE TO HELP

Want to watch a video that show how to install the TV brackets.

Watch it now at: https://youtu.be/MYjAmxcl1go Want to watch a video that show how to add the safety locks. Watch it now at: https://youtu.be/kC4JmnNCDwM

IMPORTANT SAFETY INFORMATION

• Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at supportus@perlesmith.com (US)/ supportca@perlesmith.com (CA).
• CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

Weight Restrictions If your TV weighs more, this TV stand is NOT compatible.

WARNING

• DO NOT exceed the maximum weight indicated. This TV stand is intended for use only within the maximum weights indicated.
• Use with products heavier than the maximum weights indicated may result in failure of the TV stand and its accessories, causing possible damage and or injury.

Check the VESA Pattern of TV before the Installation

• 100 mm ≈ 4 in
• 200 mm ≈ 7 7/8 in
• 300 mm ≈ 11 3/4 in
• 400 mm ≈ 15 3/4 in
• Minimum VESA pattern: 100mm/4 in(W)x100mm/4 in(H)

If your TV VESA is greater than 400×400 mm/16×16 in or less than VESA 100x100mm/4x4in, this TV stand is NOT compatible.

Tools Needed (Not lncluded)

Supplied Parts and Hardware

• WARNING: This product contains small items that could be a choking hazard if swallowed.
• Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our customer service at
  • supportus@perlesmith.com (US)/
  • supportca@perlesmith.com (CA).
• Please note: Not all hardware included in this package will be used.

1. Supplied Parts and Hardware for Step 1

2. Supplied Parts and Hardware for Step 2
   

3. Supplied Part for Step 3

4. Supplied Parts and Hardware for Step 4
   Note: The bolts and spacers are shown in accordance with the actual size

5. Supplied Part and Hardware for Step 5

Step 1 Assemble the Base

1. Step 1-1 Place foot pads [W] to the frosted side of the tempered glass base [O] in the corners

2. Step 1-2 Connect the support pillar [P] to tempered glass base [O]  Attach the top cover [Z] to the support pillar [P] Secure the support pillar [P] to tempered glass base [O] using plastic cover [Y], gasket with 3 holes [R], bolts [L] and Allen key [V]

Step 2 Connect the TV Plate [M] to Support Pillar [P]

Note: There are three choices for height adjustment. You can choose your desired height position while connecting the TV plate [M] to support pillar [P]

• Note: You may need assistance with this step.
• Connect TV plate [M] to support pillar [P] using bolts [S], washers [T] and nuts [Q]
• Note: Connect the TV plate [M] to the front side of the support pillar [P] with the bump of the TV plate facing back side of the stand.

Step 3 Secure the Wire Clips [K] to Support Pillar [P]

Step 4 Secure the TV Brackets [N] to TV

Select TV Bolts

• Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns.

  • Too short will not hold the TV.
  • Too long will damage the TV.

• Please Note: The provided TV bolts meet most of today’s TVs design. However, some TVs require special bolts which may not be in the hardware bag. In this case we offer our “PSUHP” Universal Hardware Kit which provides a large selection of bolts that can meet the demand of older and unique applications.

• Please Note: When using the spacers it is important to note that they can be used in multi-layers (meaning stacked). If you have any difficulty understanding how to install the TV bolts or spacers, please contact customer service at supportus@perlesmith.com (US)/ supportca@perlesmith.com (CA).

• CAUTION: Ensure the TV brackets [N] are EQUALLY CENTERED on your TV and securely fastened in place.

• Please note: The bolt hole locations on your TV may vary in accordance of the manufacturers design of the TV. We are only illustrating possible locations of the bolt holes.

• Option A (For Flat Back TV )

• Option B (For Round Back TV)
  

• Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.

• Option D
  For cable interference or inset holes, use spacers [H], [I] and [J] to create extra space between the TV and TV brackets

Step 5 Attach TV to the TV Plate [M] and Manage the Wires

• TV brackets are two-height-adjustable. You can choose the proper height.

1. Step 5-1 Hang the TV with brackets to the TV plate
2. Step 5-2 Push the bottom of the TV to TV plate
3. Step 5-3 Insert the safety locks [K1] into the upward facing hooks at the midway to lower part of the TV bracket. Please note this is where the lower part of the TV bracket meets the TV plate. Then tighten the bolts of the safety lock [K1] until the bolts touch the TV plate.

HEAVY! You may need assistance with this step. Thank you again for choosing this PERLESMITH product!

All of us at PERLESMITH do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. If you have any questions please don’t hesitate to contact us at

• Technical Support:
  • 1-800-556-6806 Mon-Fri 8am – 8pm(CST)
  • Other Info:
  • supportus@perlesmith.com(US)
  • supportca@perlesmith.com(CA)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>