BEGA 50601.1 LED Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

DIMENSIONS
Application
Product description
Safety
Overvoltage protection
Lamp
Installation
Cleaning · Maintenance
Replacement of the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50601.1 LED Wall Luminaire Instruction Manual

DIMENSIONS

Dimensions

Application

Wall luminaire · indoor luminaire for brilliant light with crystal glasses and aluminium luminaire housing.

The luminaire directs the light of the lamps upwards and downwards.

Product description

Luminaire made of Aluminium, finish Colour white
Crystal glasses, partially satin matt, with screw neck
Reflectors made of anodised pure aluminium 2 elongated fixing holes
Width 5mm · 76,5mm spacing
1 cable entry for mains supply cable up to ø 10.5 mm max. 5 x 1.5@
Connecting terminal 2.5@ with plug connection
Earth conductor connection
2-pole connection terminals for digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Switch®
Temporary thermal shutdown to protect
temperature-sensitive components
Safety class I
– Safety mark
– Conformity mark
Weight: 2.2 kg
This product contains light sources of energy
efficiency class(es) E

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only becarried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 16.2 W
Luminaire connected wattage 19 W
Rated temperature ta=25 °C
Ambient temperature ta max=25 °C

50 601.1K3

Module designation 2x LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 2510 lm
Luminaire luminous flux 1774 lm
Luminaire luminous efficiency 93,4 lm/W

50 601.1K4

Module designation 2x LED-0800/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 2550 lm
Luminaire luminous flux 1802 lm
Luminaire luminous efficiency 94,8 lm

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo set screw and lift off luminaire housing. Loosen push plug connection and earth connection (plug connection).

Pass the power connecting cable through the cable entry in the mounting plate.

Note position of application of the mounting plate “arrow down”.

Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.

Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection to terminal (plug connection).

The two connecting terminals marked DA, DA are provided for digital control purposes. If these terminals are not assigned, the luminaire will work with full light output. Make earth conductor connection between luminaire housing and mounting plate. Push plug into coupler as far as it will go. Install luminaire housing over mounting plateand tighten set screw. Note position of application of the luminaire “arrow down”.

Cleaning · Maintenance

Disconnect the electrical installation.
Unscrew glasses with reflectors from luminaire housing. Remove reflector retaining springs.

Clean luminaire and glasses.

Defective glass must be replaced.

Use only solvent-free cleansers.

Attach reflectors with retaining springs to glasses.

Screw glasses with reflectors into luminaire housing.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Defective glass must be replaced. Close the luminaire.

Spares