BEGA 51062.1 Track Spotlight Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 51062.1 Track Spotlight
Product Information
Product Usage Instructions
Instructions for use
Product description
Overvoltage protection
Installation
Cleaning · Maintenance
Replacing the LED module
Accessories · Optical diffuser filter
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51062.1 Track Spotlight

BEGA-51062-1-Track-Spotlight-product

Product Information

Product Name	Luminaire
Safety	The installation and operation of this luminaire are subject to

national safety regulations. Installation and commissioning may
only be carried out by a qualified electrician. The manufacturer
accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the
luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage Protection| The electronic components installed in the luminaire are
protected against overvoltage in accordance with DIN EN 61547. To
achieve an additional protection against transients, it is
recommended to use separate overvoltage protection components.
These components can be found on our website at www.bega.com.
Lamp Module Connected Wattage| 31.6W (K3), 37.5W (K4)
Luminaire Connected Wattage| 31.6W (K3), 37.5W (K4)
Rated Temperature| 25°C
Ambient Temperature| 35°C
Module Designation| LED-0800/930 (K3), LED-0800/930 (K4)
Colour Temperature| 3000K (K3), 4000K (K4)
Colour Rendering Index (CRI)| CRI > 90
Module Luminous Flux| 4220 lm (K3), 4285 lm (K4)
Luminaire Luminous Flux| 2985 lm (K3), 3031 lm (K4)
Luminaire Luminous Efficiency| 79.6 lm/W (K3), 80.8 lm/W (K4)

Product Usage Instructions

Screw the enclosed fastening ring (a) with attached reflector into the luminaire housing by turning it clockwise until it stops, so that it is fixed by clamping.
Clip the trim ring with glass and internal optical diffuser filter (b) onto the luminaire housing by applying slight pressure.
Place the surface washer adapter flush on the conductor rail in the desired position. Push the two fixing levers on the underside of the adapter to the right until they click into their end position.
Set the desired LED beam direction by turning and tilting the luminaire housing.
To unlock the adapter, move the two fixing levers in opposite directions until they disengage.

Instructions for use

Application
Ceiling mounted track spotlight · indoor luminaire for 3-phase Eurostandard- Plus® track systems.
The optical system of the washer is swivel-mounted and rotatable.
Symmetrical wide beam light distribution. Optical diffuser filters are available as accessories for changing the light distribution. With BEGA Hybrid Optics® : Highly efficient and low-loss light distribution, thanks to reflector and optical lens.

Product description

GENIUS Track spotlight with adapter Cast aluminium luminaire housing, finish Colour velvet white,
Polycarbonate track adapter with integrated LED power supply unit
Trim ring · Chrome finish
Safety glass, with internal optical diffuser filter Optical silicone lens
BEGA Hybrid Optics® Reflector surface made of pure aluminium LED power supply unit
220-240 V y 50/60 Hz
DALI-controllable
Basic insulation is provided between the mains and control cables
Safety class II 2
– Conformity mark
Weight: 1.1 kg
This product contains light sources of energy efficiency class(es) E

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage: 31.6 W
Luminaire connected wattage: 37.5 W
Rated temperature: 37.5 W
Ambient temperature: ta max = 35 °C

51 062.1 K3

Module designation: LED-0800/930
Colour temperature: 3000 K
Colour rendering index Module: CRI > 90
luminous flux Luminaire: 4220 lm
luminous flux Luminaire: 2985 lm
luminous efficiency: 79,6 lm / W

51 062.1 K4

Module designation: 79,6 lm / W
Colour temperature: 4000 K
Colour rendering index: CRI > 90
Module luminous flux: 4285 lm
Luminaire luminous flux: 3031 lm
Luminaire luminous efficiency: 80,8 lm / W

Light technique

Track spot · surface washer with adjustable optical system.
Optical system 0-340° swivel-mounted and ± 310° infinitely rotatable around the vertical luminaire axis.
Symmetrical wide beam light distribution. Half beam angle 70°
The symmetrical light cone can be changed to a flat beam, symmetrically diffuse or asymmetrical light distribution for special lighting applications by replacing the optical diffuser filter (standard) – accessoires.

For flat beam light distribution:

Diffusing filter 13 288
For symmetrical diffuse light distribution: Diffusing filter 13 312
For asymmetrical light distribution: Diffusing filter 13 311

Standard

ﬂat beam

symmetrically diffuse

asymmetrical

The light cone can be adjusted by ±360° by turning the trim ring.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. The track spotlight with adapter is ready for operation in 3-phase EUROSTANDARD-PLUS® track systems. The mounting is done without tools in the bus bar.

IMPORTANT:
Ensure that the adapter’s two lateral stays are located on the same side as the matching guide profile of the track before installing the adapter in the 3-phase EUROSTANDARD-PLUS® track system. To select the phase ( 1 2 3 ) the turning knob on the rear side of the adapter has to be operated accordingly. Screw enclosed fastening ring (a) with attached reflector into the luminaire housing by turning it clockwise until it stops, so that it is fixed by clamping. BEGA-51062.1-Track-Spotlight-fig-8

Clip the trim ring with glass and internal optical diffuser filter (b) onto the luminaire housing by applying slight pressure. BEGA-51062.1-Track-
Spotlight-fig-9

Place the surface washer adapter flush on the conductor rail in the desired position. Push the two fixing levers on the underside of the adapter to the right until they click into their end position. Set the desired LED beam direction by turning and tilting the luminaire housing. Move the two fixing levers in opposite directions until they disengage to unlock the adapter.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools. Disconnect the system and open the luminaire. Uninstall the reflector. Please follow the installation instructions for the LED module. Install the reflector. Defective glass must be replaced. Close the luminaire.