BEGA 50 898.6 Recessed Ceiling Downlight for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

DIMENSIONS
Application
Product description
Safety
Overvoltage protection
Installation into inserted ceilings:
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**BEGA 50 898.6 Recessed Ceiling Downlight for Indoor Use Instruction Manual

**

DIMENSIONS

Application

Recessed ceiling luminaire · indoor luminaire with symmetrical wide beam light distribution for connection to external LED power supply unit.

For installation into suspended ceilings with a shallow depth in interior areas.

Product description

Recessed ceiling luminaire downlight »STUDIO
LINE« without power supply unit
Cast aluminium luminaire housing,
finish Colour velvet black, inside hue matt copper
Trim ring · Chrome finish
Light-diffusing silicone lens
Reflector made of pure anodised aluminium
Fixing is achieved by using two adjustable wedge-shaped claws
1 connecting cable with strain relief and plug
connector system for BEGA power supply unit, on/off or DALI
Safety class III 3
– Conformity mark
Weight: 0.65 kg
This product contains light sources of energy
efficiency class(es) E

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp
Module connected wattage 8.5 W
Luminaire connected wattage 10.2 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C

50 898.6K3
Module designation LED-0986/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1200 lm
Luminaire luminous flux 774 lm
Luminaire luminous efficiency 75,9 lm/W

Lighting technology
Half beam angle 24°

Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

A separate power supply unit is required to operate the luminaire. For connection to external LED-power supply unit – accessory 13 143 or 13 168 – the luminaire is equipped with a 2-pin connector. Note operating instructions of the LED-power supply units.

The recessed opening is covered by the frame of the luminaire housing. Fixing of the luminaire in the structure is achieved by using two adjustable wedgeshaped claws.

Installation into concrete ceilings:
For the installation of luminaire and external power supply unit we recommend to use installation housing 10 440.

Please note:
To ensure that the luminaire is securely held in the plastered installation housing, it is essential to unscrew the screws on the underside of the fastening claws and remove the adapter for the fastening claws (see drawing).

Installation into inserted ceilings:

A recessed opening of ø 95 mm is necessary to accept the luminaire housing. Recessed depth min. 55 mm.

The claws catch the ceiling facing from the back side. The minimum thickness of the panel must be 3 mm and the maximum thickness 18 mm. If the ceiling facing has a thickness of less than 3 mm or in case of an installation intoplasterboard ceilings, the facing thickness in the region of the claws must be increased from the back side.

If the ceiling cladding is thicker, it is essential to unscrew the screws on the underside of the mounting claws and remove the adapter for the mounting claws (see drawing).

The minimum thickness of the ceiling cladding must be 13 mm and the maximum 33 mm.

Connect plug part of the luminaire with power supply unit. Push external LED power supply unit and luminaire housing into the ceiling cut-out.Tighten evenly screws of claw fasteners. Screw enclosed trim ring with attached reflector into the luminaire housing by turning it clockwise.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to thoseof the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the electrical installation. Open the luminaire. Please follow the installation instructions for the LED module. Close the luminaire.