BEGA 51 054.5 Track Spotlight for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
51 054.5 Track Spotlight for Indoor Use
Instruction Manual
Technical amendments reserved
**** 51 054.5
51 054.5 Track Spotlight for Indoor Use
Track spotlight for indoor use 
Instructions for use
Application
Ceiling mounted track spotlight · indoor luminaire for 3-phase Eurostandard-
Plus ® track systems.
The optical system of the washer is swivelmounted and rotatable.
Asymmetrical wide beam light distribution.
Product description
Track spotlight with adapter
Cast aluminium luminaire housing, finish Colour velvet black, Polycarbonate
track adapter with integrated LED power supply unit
Safety glass with optical texture
Reflector surface made of pure aluminium BEGA Vortex Optics®.
Light-diffusing synthetic LED cover
LED power supply unit 220-240 V y 50/60 Hz
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
Safety class II
**** – Conformity mark
Weight: 0.65 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 21.6 W |
|---|---|
| Luminaire connected wattage | 25 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 30 °C |
| Service life criteria | 50 000 h / L70 |
51 054.5 K3
| Module designation | LED-1222/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2670 lm |
| Luminaire luminous flux | 1505 lm |
| Luminaire luminous efficiency | 60,2 lm / W |
51 054.5 K4
| Module designation | LED-1222/940 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2770 lm |
| Luminaire luminous flux | 1561 lm |
| Luminaire luminous efficiency | 62,4 lm / W |
Light technique
Track spot · surface washer with adjustable optical system.
Optical system 0-340° swivel-mounted and ± 310° infinitely rotatable around
the vertical luminaire axis.
Asymmetrical wide beam light distribution.
Half beam angle 47/45°
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
The track spotlight with adapter is ready for operation in 3-phase
EUROSTANDARD-PLUS ® track systems.
The mounting is done without tools in the bus bar.
IMPORTANT:
Ensure that the adapter’s two lateral stays are located on the same side as
the matching guide profile of the track before installing the adapter in the
3-phase EUROSTANDARDPLUS ®track system.
To select the phase ( 1 2 3 ) the turning knob on the rear side of the adapter
has to be operated accordingly.
Place the surface washer adapter flush on the conductor rail in the desired
position.
Push the two fixing levers on the underside of the adapter to the right until
they click into their end position.
Set the desired LED beam direction by turning and tilting the luminaire
housing.
Move the two fixing levers in opposite directions until they disengage to
unlock the adapter.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The replacement can be carried out by
a qualified person using standard tools.
Disconnect the system and open the luminaire.
Uninstall the reflector.
Please follow the installation instructions for the LED module.
Install the reflector. Defective glass must be replaced. Close the luminaire.
Spares
| LED power supply unit | DEV-0438/700i |
|---|---|
| LED module 3000 K | LED-1222/930 |
| LED module 4000 K | LED-1222/940 |
| Trim frame with glass | 75 004 900 |
| Reflector | 76 001 548 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>