BEGA 51217.6 Wall Luminaire Instructions
- June 12, 2024
- BEGA
Table of Contents
11.22 • Technical amendments reserved
51 217.6
Wall luminaire for indoor use
Instructions for use
Application
Wall luminaire · Indoor luminaire with velvet white metal housing.
Luminaire with light source shielded to the front and metallic inside colour
of the reflection surface.
Radial light emission 360°.
Product description
Wall luminaire “STUDIO LINE”
Luminaire housing made of aluminium, surface Colour velvet white inside hue
matt copper
Inside synthetic cover, translucent white 3 fixing holes ø 4.5 mm
Angle 120° · Pitch circle ø 185 mm 1 cable entry for through-wiring for mains
cable
Connection terminal 2.5
Earth conductor connection 2-pole connecting terminal for digital control
LED power supply unit
220-240 V 0/50-60 Hz
DC 196-250 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
- Conformity mark
Weight: 5.5 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components. You can find them on our
website at www.bega.com.
Lamp
Module connected wattage 32.8 W
Luminaire connected wattage 36.5 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C
51 217.6K3
Module designation LED-1174/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 5100 lm
Luminaire luminous flux 340 lm
Luminaire luminous efficiency 9,3 lm/W
- preliminary data
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Remove the mounting plate with LED unit from its packaging.
Please note: A round blank made of synthetic material covers the mains
connection compartment. For the mains supply connection, this synthetic round
blank must be removed and refitted after the mains supply connection.
Loosen the black knurled screw (slotted) and remove the round made of
synthetic material from the LED unit.
Pass the power connecting cable through the cable entry in the mounting plate.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface.
Establish the earth conductor connection on the earthing screw ( ) of the
mounting plate. Make the electrical connection to the terminals. Observe the
correct configuration of the connecting cable. Connect the live conductor to
the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control
purposes. If these terminals are not assigned, the luminaire will work with
full light output. Insert the round made of synthetic material back into the
LED unit and tighten the black knurled screw (slotted).
Remove the luminaire housing (reflector) from its packaging and carefully
guide over the LED unit.
Place the luminaire housing (reflector) over the keyholes onto two threaded
bolts of the LED unit and turn it clockwise until it stops.
Tighten the two hex nuts M4 over the keyholes. Remove the supplied radial
synthetic cover with round housing cover from the packaging, guide onto the
centre of the grub screw of the LED unit and hand-tighten in the clockwise
direction.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module ·
Replacing the power supply unit
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The replacement can be carried out by
a qualified person using standard tools.
Disconnect the system from the power supply. Loosen the radial synthetic cover
with round housing cover by turning it anti-clockwise from the LED unit.
Loosen the black knurled screw (slotted) and remove the round made of
synthetic material from the LED unit.
Disconnect the earth conductor connection and the electrical connection to the
terminal. Loosen the mounting screws of the power supply unit, the round blank
bracket and earthing screws (Torx).
Remove the pot with LED module. Install the replacement pot.
Please follow the installation instructions for the LED module.
Replace defective LED power supply unit. Tighten the mounting screws of the
power supply unit, the round blank bracket and earthing screws (Torx) again.
Establish the earth conductor connection on the earthing screw ( ) of the
mounting plate. Make the electrical connection to the terminals. Observe the
correct configuration of the connecting cable. Connect the live conductor to
the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control
purposes. If these terminals are not assigned, the luminaire will work with
full light output. Insert the round made of synthetic material back into the
LED unit and tighten the black knurled screw (slotted).
Guide the radial synthetic cover with round housing cover onto the centre of
the grub screw of the LED unit and hand-tighten in the clockwise direction.
Spares
LED power supply unit DEV-0305/700i
LED module 3000 K LED-1174/930
Reflector 71 003 526 B15
Component round blank 75 005 268
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>