BEGA 50647.2 Ceiling and Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50647.2 Ceiling and Wall Luminaire
Product Information
- Product description: Luminaire made of Aluminium, finish Stainless steel Hand-blown crystal glass, white inside, with screw-neck
- Silicone gasket for protection
- Distance apart: 220 mm
- Safety class: I
- Protection class: IP 64 (Dust-tight and protection against splash water)
- Impact strength: IK06
- Weight: 2.6 kg
- Energy efficiency class: D
- Contains light sources of energy efficiency class(es) D
Product Usage Instructions
- The installation and operation of this luminaire should comply with national safety regulations.
- Installation and commissioning should only be carried out by a qualified electrician.
- The manufacturer is not liable for any damage caused by improper use or installation.
- If modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve additional protection against transients, it is recommended to use separate overvoltage protection components.
- Ensure the proper connection of the protective conductor (plug contact).
- Strip the power supply cable.
- Secure the luminaire to the mounting surface using suitable fastening material.
- Make sure to use the included gaskets.
- Establish the connection of the protective conductor to the plug device.
- Make the electrical connection to the plug device.
- Pay attention to the correct positioning of the gasket.
- Avoid touching the light output opening of the LED directly during installation or relamping.
- Loosen the hexagon socket head cap screws (4x).
- Disassemble the LED module.
- Loosen the LED-connection and earth connection (plug connection).
Dimention
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of aluminium and hand-blown
crystal glass. For a variety of interior lighting applications.
Product description
Luminaire made of Aluminium, finish Stainless steel Hand-blown crystal glass,
white inside, with screw-neck Silicone gasket 2 mounting holes ø 5.5 mm
Distance apart 220 mm 2 cable entries for through-wiring for mains cable up to
ø 10.5 mm max. 3 × 1.5@ Connecting terminal 2.5@ with plug connection Earth
conductor connection LED power supply unit 220-240 V x 0/50-60 Hz DC 170-280 V
BEGA Thermal Switch® Temporary thermal shutdown to protect temperature-
sensitive components Safety class I Protection class IP 64 Dust-tight and
protection against splash water Impact strength IK06 Protection against
mechanical impacts < 1 joule r – Safety mark c – Conformity mark Weight: 2.6
kg This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
- Lamp
- Module connected wattage 19.3 W
- Luminaire connected wattage 22.5 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 40 °C
- 50 647.2 K3
- Module designation LED-0832/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 3165 lm
- Luminaire luminous flux 1427 lm
- Luminaire luminous efficiency 63,4 lm / W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Loosen
hexagon socket head cap screws (4x). Disassemble LED module. Loosen LED-
connection and earth connection (plug connection). Dismantle the mains supply
cable. Lead mains supply cable through the cable entry into the luminaire
housing. Fix the luminaire housing with enclosed or any other suitable fixing
material onto the mounting surface. It is imperative to use the enclosed
gaskets. Push silicone sleeves over the lines. Make earth conductor connection
to plug connection. Push silicone sleeves over the lines and make electrical
connection to plug connection. Make earth connection between LED module and
luminaire housing (plug connection). Push LED plug into coupler as fa as it
will go. Assemble LED module. Tighten the hexagon socket head cap screws
evenly (4x). Please observe that the LED module is not damaged mechanically.
Fix glass to the luminaire housing by turning it clockwise. Make sure that
gasket is positioned correctly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt. Defective
glass must be replaced.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. Inspect and,
if necessary, replace the luminaire gaskets. Defective glass must be replaced.
Close the luminaire.
Spares
- Spare glass 11 003 083 47R G
- LED power supply unit DEV-0277/500
- LED module 3000 K LED-0832/930
- Gasket 83 000 372
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>