BEGA 51217.4 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 51217.4 Wall Luminaire
Product Information
Product Usage Instructions
Dimension
Instructions for use
Product Description
Installation
Documents / Resources

BEGA 51217.4 Wall Luminaire

Product Information

Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients and other issues, we recommend using separate overvoltage protection components. You can find them on our website at www.bega.com.
Lamp Module connected wattage: 32.8 W
Luminaire connected wattage: 36.5 W
Rated temperature: 25-40°C
Ambient temperature: 25-40°C
Lamp: LED-1174/930
Color temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 5100 lm
Luminaire luminous flux: 850 lm
Luminaire luminous efficiency: 23.3 lm/W

Product Usage Instructions

Place the luminaire housing (reflector) over the keyholes onto two threaded bolts of the LED unit and turn it clockwise until it stops.
Tighten the two hex nuts M4 over the keyholes.
Remove the supplied radial synthetic cover with a round housing cover from the packaging.
Guide the cover onto the center of the grub screw of the LED unit and hand-tighten it in the clockwise direction.

Spares

LED power supply unit: DEV-0305/700i
LED module 3000 K: LED-1174/930
Reflector Component round blank: 71 003 526 B14
Module LED 3000 K: 75 005 268

Dimension

BEGA-51217-4-Wall-Luminaire-FIG-1

Instructions for use

Application

Wall luminaire · Indoor luminaire with velvet white metal housing.
Luminaire with light source shielded to the front and metallic inside colour of the reflection surface.
Radial light emission 360°.

Product Description

Wall luminaire “STUDIO LINE”
Luminaire housing made of aluminum, surface Colour velvet white inside hue matt brass
Inside the synthetic cover, translucent white 3 fixing holes ø 4.5mm
Angle 120° · Pitch circle ø 185mm
1 cable entry for through-wiring for mains cable
Connection terminal 2.5@
Earth conductor connection 2-pole connecting terminal for digital control
LED power supply unit 220-240 V x 0/50-60 Hz
DC 196-250 V
DALI-controllable
Number of DALI addresses : 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Conformity mark
Weight: 5.5 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage 32.8 W
Luminaire connected wattage 36.5 W
Rated temperature ta=25 °C
Ambient temperature ta max =40 °C

51 217.4K3

Module designation LED- 1174/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 5100 lm
Luminaire luminous flux 850 lm
Luminaire luminous efficiency 23,3 lm/W

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove the mounting plate with LED unit from its packaging.
Please note: A round blank made of synthetic material covers the mains connection compartment. For the mains supply connection, this synthetic round blank must be removed and refitted after the mains supply connection.
Loosen the black knurled screw (slotted) and remove the round made of synthetic material from the LED unit.
Pass the power connecting cable through the cable entry in the mounting plate
Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
Establish the earth conductor connection on the earthing screw (1) of the mounting plate.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control purposes.
If these terminals are not assigned, the luminaire will work with full light output.
Insert the round made of synthetic material back into the LED unit and tighten the black knurled screw (slotted).
Remove the luminaire housing (reflector) from its packaging and carefully guide over the LED unit.
Place the luminaire housing (reflector) over the keyholes onto two threaded bolts of the LED unit and turn it clockwise until it stops.
Tighten the two hex nuts M4 over the keyholes.
Remove the supplied radial synthetic cover with round housing cover from the packaging, guide onto the centre of the grub screw of the
LED unit and hand-tighten in the clockwise direction.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

Replacing the power supply unit
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
Disconnect the system from the power supply.
Loosen the radial synthetic cover with round housing cover by turning it anti-clockwise from the LED unit.
Loosen the black knurled screw (slotted) and remove the round made of synthetic material from the LED unit.
Disconnect the earth conductor connection and the electrical connection to the terminal.
Loosen the mounting screws of the power supply unit, the round blank bracket and earthing screws (Torx).
Remove the pot with LED module. Install the replacement pot.
Please follow the installation instructions for the LED module.
Replace defective LED power supply unit.
Tighten the mounting screws of the power supply unit, the round blank bracket and earthing screws (Torx) again.
Establish the earth conductor connection on the earthing screw (1) of the mounting plate.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control purposes.
If these terminals are not assigned, the luminaire will work with full light output.
Insert the round made of synthetic material back into the LED unit and tighten the black knurled screw (slotted).
Guide the radial synthetic cover with round housing cover onto the centre of the grub screw of the LED unit and hand-tighten in the clockwise direction.