HORMANN FUS 2 BiSecur Recessed Radio Transmitter Instruction Manual

HORMANN FUS 2 BiSecur Recessed Radio Transmitter

About these instructions

These instructions are divided into a text section and an illustrated section. They contain important information on the product, and especially safety instructions and warnings.

• Read through the instructions carefully.
• Keep these instructions in a safe place.

Definitions used

System

A door with the associated operator

Dissemination as well as duplication of this document and the use and communication of its content are prohibited unless explicitly permitted. Noncompliance will result in damage compensation obligations. All rights reserved in the event of patent, utility model or design model registration.

Equipment/ system

A product with radio receiver, e.g. relay receiver, radio socket receiver.

Status

The current position of a door or the current status of an equipment/ system.

Symbols used

Important note for avoiding material damage and personnel injury

Abbreviations Used

Colour code for cables, single conductors and components
The colour abbreviations for cable and strand identification and for components conform to the international colour code in accordance with IEC 60757:

GN| Green| BU| Blue
RD| Red| |

Safety instructions

Intended use

The recessed radio transmitter FUS 2 BiSecur is a bi-directional transmitter for door operators and radio equipment. The recessed radio transmitter has two channels. It can be operated via externally connected transmitter buttons with both the BiSecur radio and the fixed code 868 MHz.

Other applications are not permitted. The manufacturer is not liable for damages caused by improper use or incorrect operation.

Safety instructions for teach-in and operation

WARNING

Risk of injury during intended or unintended door travel

• Make sure that the recessed radio transmitters are kept away from children and can only be used by people who have been instructed on how the remote-control system functions!
  If the door has only one safety feature, only operate the recessed radio transmitter if you are within sight of the door!

• Drive or walk through the door openings of remote-controlled systems only when the door is in the Open end-of-travel position!

• Never stand in the door’s area of travel.

• Note that accidentally pressing a button on the hand transmitter can result in door travel.

• Pay attention that no persons or objects are in the system’s area of travel when teaching in the radio system.

CAUTION
Danger through unintended activation of equipment

The remote-controlled operation of equipment can result in unintended activation, for example, machines can be actuated.

▶ Ensure that the remote-controlled operation of equipment does not result
in danger to persons or objects or that these risks are covered by safety equipment.

▶ Observe the manufacturer information for the remote-controlled devices.

▶ The unintentional activation of machines must not be possible.

NOTES

• If there is no separate entrance, perform changes and extensions of radio systems while standing in the facility.
• After programming or extending the radio system, you have to perform a function check.
• Local conditions may affect the range of the radio system.

Scope of delivery

• Recessed radio transmitter FUS 2 BiSecur
• 1 × 1.5 V battery, type: AAA (LR03), alkali-manganese
• Operating instructions

Product description (see Figure 1 )

1. Housing
2. LED, bi-colour
3. Battery
4. GN, T2 Connecting terminal, second transmitter button
5. RD,T1 Connecting terminal, first transmitter button
6. BU, C Connecting terminal, joint non-volt-free contact

Installation (see Figure 2 and 3 )

NOTE
If the connecting lead T2 is not connected, the cable must be insulated

Fitting (see Figure 4 )

The choice of the fitting location affects the range.

• Prior to fitting, verify that the radio signal can reach the system or the equipment at the selected fitting site.
  • Determine the best orientation, by trial and error, if required.

Initial start-up

After inserting the battery, the recessed radio transmitter is ready for operation.

Inserting / changing the battery (see Figure 5 )

WARNING
Risk of explosion due to incorrect battery type

• Use only this battery type: 1 × 1.5 V, type: AAA (LR03), alkali-manganese
• Remove the battery from the recessed radio transmitter if it is out of use for a long period of time.

Proper disposal: See section 12

Operation

Each connected transmitter button is assigned to a radio code.

• Press the transmitter button whose radio code you want to transmit.
  • The LED is illuminated blue for 2 seconds.
  • The radio code is transmitted.

Learning behaviour of inherited radio codes

If the radio code for the transmitter button has been inherited from a hand transmitter and is being used for the first time, proceed as follows depending on the product:

Garage door operator series 4, roller garage door operator series 2, receiver ESE BS HCP

• Press and hold the transmitter button until the LED flashes alternately in red and blue and the desired function is performed.

All other products

• Press the transmitter button a second time.

Learning and inheriting /transmitting a radio code

WARNING
Risk of injury during intended or unintended door travel

• See warning in section 2.2.

Teaching in a radio code (see Figure 6 )

After you have gone through the individual steps to teach in an access code, the LED will be illuminated in blue or red and you will hear signal tones. The displays and tones vary according to the function.

• Please see section 11 for an explanation.

1. Hold the hand transmitter A to the right of the recessed radio transmitter.
2. Press and hold the hand transmitter button whose radio code is to be inherited.
   • The LED is illuminated blue for 2 seconds and then goes out.
   • After 5 seconds, the LED alternates flashing in red and blue.
   • The hand transmitter sends the radio code.
3. Press and hold the connected transmitter button that should learn the radio code.
   • The LED is illuminated blue for 2 seconds and then goes out.
   • The LED will flash slowly in blue.
   • If the radio code is recognised, the LED flashes quickly in blue.
   • After 2 seconds, the LED goes out.
4. Release the hand transmitter button and the transmitter button.
   The radio code of the hand transmitter button has been taught in to the connected transmitter button.

NOTE

You have 15 seconds to inherit / transmit the radio code. If inheriting / transmitting the code was not successful within this period of time, repeat the process.

Mixed operation / BiSecur and fixed code 868 MHz

If BiSecur radio is configured, mixed operation (BiSecur and fixed code 868 MHz) is possible. The radio internal push button can learn radio codes from older hand transmitters (grey hand transmitter with blue buttons or device designation HSD2-868) with fixed code 868 MHz.

Reset

After you have gone through the individual steps for a reset, the LED will be illuminated in blue or red and you will hear signal tones. The displays and tones vary according to the function.

• Please see section 11 for an explanation.

Each connected transmitter button is assigned to a new radio code by means of the following steps.

1. Open the housing of the recessed radio transmitter.

2. Remove the battery for 10 seconds.

3. Push a connected transmitter button.

4. Keep the transmitter button pressed.

5. Insert the battery.

   • The LED slowly flashes in blue for 4 seconds.
   • The LED flashes rapidly in blue for 2 seconds.
   • The LED is illuminated blue for a long time.

6. Release the transmitter button.
   All radio codes are newly assigned.

7. Close the housing of the recessed radio transmitter

NOTE:
If you release the connected transmitter button prematurely, no new radio code
is allocated.

Setting the fixed code 868 MHz

1. Carry out steps 1 – 5 of the device reset
2. Continue to keep the transmitter button pressed.
   • The LED slowly flashes in red for 4 seconds.
   • The LED flashes rapidly in red for 2 seconds.
   • The LED is illuminated red for a long time.
3. Release the transmitter button.
   The fixed code 868 MHz has been set.

NOTE
If you release the connected transmitter button prematurely, the BiSecur radio remains active.
For more information, visit www.hoermann.com.

LED display / signal tones

Blue (BU)

learn mode.
Flashes quickly after slow flashing| Brief signal tones| A valid radio code was discovered during the learning
Flashes slowly for 4 seconds, flashes quickly for 2 seconds, is illuminated long| Long signal tones,
brief signal tones,
long signal tone| Reset is being performed and completed
Flashes twice; following this, the radio code continues to be transmitted| Long signal tones| The battery should be replaced soon
Flashes twice; following this, the radio code is no longer transmitted| Long signal tones| The battery must be replaced immediately
Flashes slowly for 4 seconds, flashes quickly for 2 seconds, is illuminated long| | The fixed code 868 MHz is being set

Blue (BU) and red (RD)

inherit / transmit mode.

Disposal

Dispose of the packaging sorted by materials

Electrical and electronic devices must be returned to the appropriate recycling facilities.

Dispose of the batteries separately. Each consumer is legally required to leave batteries with a collection point in their community, their district, or with a trader.

Technical data

Recessed radio transmitter FUS 2 BiSecur
Model FUS2-868-BS
Frequency 868 MHz
Transmitting power Max. 20 mW (EIRP)
Power supply 1 × 1.5 V battery, type: AAA (LR03), alkali-manganese
Perm. ambient temperature -20 °C to +60 °C
Max. humidity 93%, non-condensing
Protection category IP 20
Dimensions (W × H × D) 51 × 50 × 15 mm

EU and UK Declaration of Conformity

UK Ltd. herewith declares that the radio equipment type recessed transmitter FUS 2 BiSecur complies with the EU Directive 2014/53/EU and the UK Regulations 2017 No. 1206.
The complete text of the EU Declaration of Conformity and of the UK Declaration of Conformity can be found on the following website:

The complete text of the EU Declaration of Conformity and of the UK Declaration of Conformity can be found on the following website:

www.hoermann-docs.com/277113

HÖRMANN KG Verkaufsgesellschaft
Upheider Weg 94 – 98
33803 Steinhagen
Deutschland

References

• hoermann-docs.com/277113

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>