HORMANN 4553847 Hand Transmitter HSD 2 BiSecur Instruction Manual

HORMANN 4553847 Hand Transmitter HSD 2 BiSecur

These instructions are divided into a text section and an illustrated section. They contain important information on the product, and especially safety instructions and warnings.

• Read through the instructions carefully.
• Keep these instructions in a safe place

Dissemination as well as duplication of this document and the use and communication of its content are prohibited unless explicitly permitted. Noncompliance will result in damage compensation obligations. All rights reserved in the event of patent, utility model or design model registration. Subject to changes

Safety instructions

Intended use
The HSD 2 BiSecur is a unidirectional transmitter for operators and their accessories. It can be operated via BiSecur radio and the fixed code 868 MHz. Other types of application are prohibited. The manufacturer is not liable for damage caused by improper use or incorrect operation.

Safety instructions for a teach-in and operation
Risk of injury during intended or unintended door travel

• Make sure that hand transmitters are kept away from children and can only be used by people who have been instructed on how the remote-controlled door system functions!
• If the door has only one safety device, only operate the hand transmitter if you are within sight of the door!
• Drive or walk through the door openings only when the door is in the Open end-of-travel position!
• Never stand in the door’s area of travel.
• Note that accidentally pressing a button on the hand transmitter can result in door travel.
• Make sure that no persons or objects are in the door’s area of travel when teaching in the radio system.

NOTE

• If there is no separate entrance, perform changes and extensions of radio systems while standing inthe facility.
• After programming or extending the radio system, you have to perform a function check.
• Local conditions may affect the range of the radio system.

Scope of delivery

• Hand transmitter HSD 2 BiSecur
• 1 × 3 V battery, type: CR2025, lithium
• Key
• Operating instructions

Product description

1. LED, bi-colour
2. Hand transmitter buttons
3. Battery compartment cover
4. Battery
5. Key cable
6. Bolt sleeve
7. Key for
8. opening / closing the battery compartment cover and
9. tightening / loosening the screw-in sleeves
10. Battery insulation foil

Initial start-up

After removing the battery insulation foil, the hand transmitter is ready for operation (see Figure 1 , 8 ).

Changing the battery

WARNING
Risk of explosion due to incorrect battery type

• Use only this battery type : 1 × 3 V battery, type: CR2025, lithium
• Remove the battery from the hand transmitter if it is out of use for a long period of time.

WARNING
Danger to life due to swallowing battery If the battery is swallowed, serious internal burns can occur within 2 hours and result in death. Keep batteries out of the reach of children!

Proper disposal : See section 11

Operation

Each hand transmitter button is assigned a radio code. Press the button of the hand transmitter whose radio code you want to transmit.

• The LED is illuminated blue for 2 seconds.
• The radio code is transmitted

Learning behaviour of inherited radio codes If the radio code for the hand transmitter button has been inherited from a hand transmitter and is being used for the first time, proceed as follows depending on the product Garage door operator series 4, roller garage door operator series 2, receiver ESE BS HCP  Press and hold the hand transmitter button until the LED flashes alternately in red and blue and the desired function is performed

All other products
Press the hand transmitter button a second time.

Learning and inheriting / transmitting a radio code

CAUTION
Danger of injuries due to unintended door travel See warning in section 1.2

Teaching in a radio code

1. Hold hand transmitter A that is to be taught in the radio code to the left of hand transmitter B.
2. Press the hand transmitter button on hand transmitter B, whose radio code is to be inherited, and keep it pressed.
3. The LED is illuminated blue for 2 seconds and then goes out.
4. After 5 seconds, the LED alternates flashing in red and blue.
5. The hand transmitter sends the radio code.
6. Press the hand transmitter button on hand transmitter A that is to be taught in the radio code, and keep it pressed.
7. The LED is illuminated blue for 2 seconds and then goes out.
8. The LED flashes slowly in blue.
9. If the radio code is recognised, the LED flashes rapidly in blue.
10. After 2 seconds, the LED goes out.
11. Release the two hand transmitter buttons. The radio code of the hand transmitter button has been taught in.

NOTE
You have 15 seconds to inherit / transmit the radio code. If inheriting / transmitting the code was not successful within this period of time, repeat the process.

Mixed operation / BiSecur and fixed code 868 MHz
If BiSecur radio is configured, mixed operation (BiSecur and fixed code 868 MHz) is possible. The hand transmitter can learn radio codes from older hand transmitters (grey hand transmitter with blue buttons or device designation HSD2-868) with fixed code 868 MHz

Reset

Each hand transmitter button is assigned a new radio code by means of the following steps.

1. Open the battery compartment cover.
2. Remove the battery for 10 seconds.
3. Press a hand transmitter button and keep it pressed.
4. Insert the battery.
5. The LED flashes slowly in blue for 4 seconds.
6. The LED flashes rapidly in blue for 2 seconds.
7. The LED is illuminated blue for a prolonged period of time.
8. Release the hand transmitter button. All radio codes have been newly assigned.
9. Close the battery compartment cover.

NOTE
If the hand transmitter button is released prematurely, no new radio codes are assigned

Setting the fixed code 868 MHz

1. Carry out steps 1 – 4 of the device reset.
2. Keep the hand transmitter button pressed.
3. The LED slowly flashes in red for 4 seconds.
4. The LED flashes rapidly in red for 2 seconds.
5. The LED is illuminated red for a prolonged period of time.
6. Release the hand transmitter button. The fixed code 868 MHz has been set.
7. Close the housing.

NOTE
If the hand transmitter button is released prematurely, the BiSecur radio connection will remain active. For more information, visit www.hoermann.com

Fixing to a keychain

LED display

Blue (BU)

the teach-in procedure
Flashes slowly for 4 seconds, flashes

rapidly for 2 seconds, illuminated for a pro- longed period

| Device reset is being per- formed and completed

Red (RD)

The battery should be replaced soon
Flashes twice; following this, the radio code is no longer transmitted| The battery must be replaced immediately

Blue (BU) and Red (RD)

Cleaning

ATTENTION
Damaging the hand transmitter by faulty cleaning  Only clean the hand transmitter with a clean, soft cloth.

NOTE
Regular use of disinfectants can cause damage to the hand transmitter.

Disposal

Dispose of the packaging sorted by materials Electrical and electronic devices must be returned to the appropriate recycling facilities Dispose of the batteries separately. Each consumer is legally required to leave batteries with a collection point in their community, their district, or with a trader

Technical data

• Hand transmitter HSD 2 BiSecur
• Model HSD2-868-BS
• Frequency 868 MHz
• Transmitting power (EIRP) max. 10 mW
• Power supply 1 × 3 V battery, type: CR2025, lithium
• Perm. ambient temperature 0 °C to +50 °C
• Max. humidity 93%, non-condensing
• Protection category IP 20
• Dimensions (W × H × D) 32 × 66 × 13 mm

EU and UK Declaration of Conformity

Hörmann KG Verkaufsgesellschaft and Hörmann UK Ltd. herewith declares that the radio equipment type hand transmitter HSZ 1 / 2 BiSecur complies with the EU Directive 2014/53/EU and the UK Regulations 2017 No. 1206. The complete text of the EU Declaration of Conformity and of the UK Declaration of Conformity can be found on the following website: www.hoermann- docs.com/277106

HSD 2 BiSecur Hörmann KG Verkaufsgesellschaft Upheider Weg 94 – 98 33803 Steinhagen Deutschland

References

• hoermann-docs.com/277106

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>