BEGA 50813.2 Recessed Ceiling Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50813.2 Recessed Ceiling Luminaire
Product Information
| Parameter | Value |
|---|---|
| Lamp Module connected wattage | 7.8 W |
| Luminaire connected wattage | 9.8 W |
| Rated temperature | Ambient temperature |
| Colour temperature | 3000 K |
| Colour rendering index (CRI) | > 90 |
| Module luminous flux | 1180 lm |
| Luminaire luminous flux | 562 lm |
| Luminaire luminous efficiency | 57.3 lm / W |
Product Usage Instructions
- Safety: The installation and operation of this luminaire should be done in accordance with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. If modifications are made to the luminaire, the person responsible for these modifications is considered the manufacturer.
- Overvoltage Protection: The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website at www.bega.com.
- Installation: The luminaire housing and external LED power supply unit must not be covered by any heat insulating materials. During installation or relamping, avoid touching the light output opening of the LED directly.
- Replacing the LED module: The designation of the LED module is noted on a label in the luminaire. BEGA replacement modules have the same light color and light output as the originally fitted modules. Qualified persons can replace the module using standard tools. Disconnect the system, open the luminaire, follow the installation instructions for the LED module, and close the luminaire.
Recessed ceiling luminaire for indoor use
Instructions for use
Application
Recessed ceiling luminaire · indoor luminaire with symmetrical wide beam light
distribution and a remote non-dimmable power supply unit. For installation in
suspended ceilings
of 5-30 mm in interior applications.
Product description
- Recessed LED ceiling luminaire with a remote power supply unit
- Luminaire housing made of cast aluminium Ceiling trim ring finish, Colour velvet black Inside hue aluminium matt
- Fixing is achieved by using 2 fastening springs
- Recessed opening ø 100 mm
- Required installation depth 75 mm
- Light-diffusing disc
- External LED power supply unit
- 220-240 V x 0/50-60 Hz
- Safety class II
- – Safety mark
- CE– Conformity mark
- Weight: 0.35 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 7.8 W
- Luminaire connected wattage 9.8 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 45 °C
50 813.2 K3
- Module designation LED-1021/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1180 lm
- Luminaire luminous flux 562 lm
- Luminaire luminous efficiency 57,3 lm / W
Installation
Luminaire housing and external LED power supply unit must not be covered by
any heat insulating materials.
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping..
Cover the recessed opening with the stop ring of the luminaire housing.
The luminaire housing is then fixed in the recessed opening via two springs.
Installation in suspended ceilings:
A recessed opening of 100 mm with a minimum depth of 75 mm is required.
The minimal thickness of the ceiling panel must be 5 mm and must not be
greater than 30 mm. A ceiling panel with less than 5 mm thickness must be
reinforced on the reverse.
The electrical connection must be made on site in the appropriate safety class
on the LED power supply unit connecting cable. A distribution box must be
used.
Ensure the correct assignment of the connecting cable. Establish the mains
connection on the brown (L) and blue (N) wires. Guide the LED power supply
unit through the opening in the ceiling and position it on the suspended
ceiling.
Compress the fastening springs of the luminaire housing on both sides and
slide the luminaire housing into the recessed opening.
The fastening springs lock into place behind the ceiling panel.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation
instructions for the LED module.
Close the luminaire.
Spares
- LED power supply unit DEV-0375/350
- LED module 3000 K LED-1021/930
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>