BEGA 33640 Ceiling and Wall Luminaire Instructions

: June 12, 2024
: BEGA

Table of Contents

BEGA 33640 Ceiling and Wall Luminaire
DIMENSION
Product Information
Product Usage Instructions
Instructions for use
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33640 Ceiling and Wall Luminaire

DIMENSION

BABY-LOCK-XE6583001-Quilting-Guide-FIG-1

Product Information

The Decken- und Wandleuchte is a ceiling and wall luminaire madeof aluminium and hand-blown satin matt three-ply opal glass. It is designed for a variety of interior and exterior lighting applications.

The luminaire has the following specifications:

Model: 33 640
IP Rating: IP 64
Lamp Module connected wattage: 42.6 W
Luminaire connected wattage: 46.9 W
Rated temperature: 25°C
Ambient temperature: 40°C

The luminaire is equipped with LED modules that have different designations, colour temperatures, colour rendering indexes, module luminous flux, luminaire luminous flux, and luminaire luminous efficiency. These specifications are as follows:

Module Designation| Colour Temperature| Colour Rendering Index| Module Luminous Flux| Luminaire Luminous Flux| Luminaire Luminous Efficiency
---|---|---|---|---|---
LED-0630/830| 3000 K| CRI > 80| 7375 lm| 3640 lm| 77.6 lm / W
LED-0630/840| 4000 K| CRI > 80| 7480 lm| 3692 lm| 78.7 lm / W

Product Usage Instructions

Safety: The installation and operation of the luminaire must comply with national safety regulations. Only qualified electricians should carry out the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. Any modifications to the luminaire should be done by the responsible person and will be considered as the manufacturer’s responsibility.

Overvoltage Protection: The luminaire comes with built-in protection against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website at www.bega.com.

Instructions for use

Application
Ceiling and wall luminaire made of aluminium and hand-blown satin matt three- ply opal glass. For a variety of interior and exterior lighting applications.

Product description

Luminaire made of aluminium and stainless steel
BEGA Unidure® coating technology
Opal glass, satin matt, with screw neck Silicone gasket 3 fixing holes ø 5.5 mm
Angle 120° · Pitch circle ø 400 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-276 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 64
Dust-tight and protection against splash water Impact strength IK05
Protection against mechanical impacts < 0.7 joule
- r – Safety mark
- c – Conformity mark

Weight: 6.4 kg
This product contains light sources of energy efficiency classes D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at: www.bega.com.

Lamp

Module connected wattage 42.6 W
Luminaire connected wattage 46.9 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

33 640 K3

Module designation: LED-0630/830
Colour temperature: 3000 K
Colour rendering index: CRI > 80
Module luminous flux: 7375 lm
Luminaire luminous flux: 3640 lm
Luminaire luminous efficiency: 77,6 lm / W

33 640 K4

Module designation: LED-0630/840
Colour temperature: 4000 K
Colour rendering index: CRI > 80
Module luminous flux: 7480 lm
Luminaire luminous flux: 3692 lm
Luminaire luminous efficiency: 78,7 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo screws key slots and remove the LED-unit.
Pull off plug parts (L,N) and (DA,DA) on the plug-in device.
Pull off the earth conductor plug connector of the LED device in the luminaire base.
Lead the mains supply cable through the cable entry into the luminaire housing.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Place the earth conductor plug connector of the LED device in the luminaire base.
Press plug parts (L,N) and (DA,DA) firmly into the plug-in devices.
Reassemble LED-unit and tighten fixing screws firmly and evenly. Please observe that the LED board is not damaged mechanically.
Screw glass clockwise into the luminaire base against the gasket .
Make sure that gasket is positioned correctly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares