BEGA 50684.4 Recessed Ceiling Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50684.4 Recessed Ceiling Luminaire
Product Information
- Safety: The installation and operation of this luminaire are subject to national safety regulations. A qualified electrician should do installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation.
- Overvoltage Protection: The luminaire has built-in protection against overvoltage. Additional overvoltage protection components can be found on the manufacturer’s website.
- Lamp Module: The connected wattage of the lamp module is 8.1W, and the luminaire-connected wattage is 9.8W. When installed in heat-insulating material, the rated temperature is between 5°C and 25°C.
- Module Designation: The module designation is LED-0800/930 with a color temperature of 3000K. The color rendering index (CRI) is greater than 90. The module has a luminous flux of 1255lm, and the luminaire has a luminous flux of 861lm with a luminaire luminous efficiency of 87.9lm/W.
- Notice prior to installation: Additional filler is required for flush installation of the recessed housing in the suspended ceiling.
Product Usage Instructions
- Connect the LED power supply unit to the luminaire.
- Route the LED power supply unit through the installation housing and place it in the suspended ceiling.
- Connect the 2-pin plug connector between the luminaire and the external LED power supply unit.
- Press together the two internal fixing sliders inside the luminaire housing.
- Push the luminaire housing to the end of the installation housing and release the fixing sliders. This secures the luminaire housing inside the installation housing.
- Place the reflector with silicone lens on the ceiling trim ring.
- Twist the ceiling trim ring, along with the attached reflector, to the right to fix the assembly inside the luminaire housing.
- To replace the LED module, disconnect the system and open the luminaire.
- Follow the installation instructions for the LED module, ensuring that the replacement module matches the original module in terms of light color and output.
- Close the luminaire after replacing the LED module.
Note: The power supply units are only suitable for operating one LED luminaire. Additional instructions for accessories can be provided upon request.
Recessed ceiling downlight for indoor use
Instructions for use
Application
Recessed ceiling luminaire · indoor luminaire with symmetrical wide beam light
distribution for connection to external LED power supply unit. For flush-
mounting installation in indoor suspended ceilings of 5-25 mm thickness.
Product description
Recessed ceiling luminaire downlight »STUDIO LINE« without power supply unit Luminaire housing made of cast aluminium The recessed housing is made of glass fibre reinforced synthetic material Centre-plate made of rigid polystyrene foam Trim ring, Colour velvet black Reflector made of pure anodised aluminium Inside hue matt brassRecessed opening ø 125 mm Required installation depth 95 mm 1 connecting cable with strain relief and plug connector system for BEGA power supply unit, on/off or DALISafety class III 3 c – Conformity mark Weight: 0.55 kg This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
- Module connected wattage 8.1 W
- Luminaire connected wattage 9.8 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 55 °C
- When installed in heat-insulating material ta max = 35 °C
50 684.4 K3
- Module designation LED-0800/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1255 lm
- Luminaire luminous flux 861 lm
- Luminaire luminous efficiency 87,9 lm / W
Notice prior to installation:
Additional filler is required for the flush installation of the recessed
housing in the suspended ceiling.
Installation
A separate power supply unit is required to operate the luminaire. For connection to external LED-power supply unit – accessory 13 143 or 13 168 – the luminaire is equipped with a 2-pin connector. Note operating instructions of the LED-power supply units. LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. The recessed housing is fixed in the recessed opening by screwing it to the ceiling from below.
Installation in suspended ceilings:
A recessed opening of 125 mm with a minimum depth of 95 mm is required. The
lateral clearance between the recessed housing and parts of the building must
be at least 50 mm. Make the appropriate cutout in the suspended ceiling. The
ceiling cutout must have an all-round chamfer of 45°, depending on the
thickness of the ceiling panel.
Remove the ceiling mounting plate by turning it upwards and out of the thread
of the adjusting sleeve, move it through the ceiling cutout and place it on
the suspended ceiling. Secure the ceiling mounting plate with screws (Ø 3.5 to
4 mm) suitable for gypsum plasterboard panels from below through the suspended
ceiling. When doing so, hold the ceiling mounting plate through the ceiling
cutout.
Turn the adjusting sleeve into the thread of the previously fitted ceiling mounting plate until it is exactly flush with the ceiling.
IMPORTANT:
Make sure to use this centre-plate in order to guarantee the correct
installation of the luminaire in the ceiling! Fill the 45° chamfer of the
ceiling cutout with standard filler and smooth it so that it is flush. Allow
the filler to set completely! Press the centre plate about 5 mm upwards into
the adjusting sleeve and then pull it down carefully to remove it from the
adjusting sleeve.
Connect to the LED power supply unit. Route the LED power supply unit throughthe installation housing and place it in the suspended ceiling. Connect the 2-pin plug connector between luminaire and external LED power supply unit. Press together the two internal fixing sliders inside the luminaire housing. Push the luminaire housing to the end of the installation housing and then release the fixing sliders. This mechanism ensures that the luminaire housing sits securely inside the installation housing. Place the reflector with silicone lens on the ceiling trim ring. Twist the ceiling trim ring complete with the attached reflector to the right to fix the assembly inside the luminaire housing.
Light technique
Symmetrical wide beam light distribution Half beam angle 34°
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. Close the
luminaire.
Accessories
Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
- 13 143 Power supply unit on/off
- 13 168 Power supply unit DALI
The power supply units are only suitable for the operation of one LED luminaire. For the accessories a separate instructions for use can be provided upon request.
Spares
- Centre-plate 06 000 418
- Trim ring 20 000 043 B1
- LED module 3000 K LED-0800/930
- Reflector 75 002 764
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com