BEGA 50 567.1 Ceiling Luminaires Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50 567.1 Ceiling Luminaires
Product Information
Product Usage Instructions
Ceiling luminaire for indoor use
Instructions for use
Installation
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50 567.1 Ceiling Luminaires

Product Information

Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.

Overvoltage protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients, it is recommended to use separate overvoltage protection components.

Module designation: LED-0800/927
Colour temperature: 2700 K
Colour rendering index (CRI): > 90
Module luminous flux: 1665 lm
Luminaire luminous flux: 1333 lm
Luminaire luminous efficiency: 98.7 lm / W
Module designation: LED-0800/930
Colour temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 1735 lm
Luminaire luminous flux: 1389 lm
Luminaire luminous efficiency: 102.9 lm / W

Product Usage Instructions

Installation:
- Avoid touching the light output opening of the LED directly during installation or relamping.
- Ensure a secure connection by positioning the luminaire housing precisely in relation to the mounting plate. Make sure the vertical bar inside the housing aligns with the mounting hole on the long bar of the mounting plate. Press the housing firmly against the plate and turn it clockwise until it stops.
Open Luminaire:
- Unscrew the glass from the luminaire housing by turning it counter-clockwise. Hold the housing in place with one hand to prevent it from turning on the mounting plate.
Replacement of the LED module:
- The designation of the LED module is noted on a label in the luminaire.
- To replace the module, disconnect the system and open the luminaire. Follow the installation instructions for the LED module provided by the manufacturer.
- If the glass is defective, replace it before closing the luminaire.

Ceiling luminaire for indoor use

Instructions for use

Application
Ceiling luminaire Indoor luminaire with wide beam light distribution.

Product description Aluminium alloy housing, finish Colour velvet white
Crystal glass, partially satin matt, with screw neck
Reflector made of pure anodised aluminium 2 mounting holes ø 4.5 mm
Distance apart 112 mm
The luminaire is suitable for through-wiring. Connecting terminals 2.5@
Earth conductor connection
LED power supply unit: 220-240 V x 0/50-60 Hz
DC 176-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK06
Protection against mechanical
impacts < 1 joule
Safety mark
CE: Conformity mark
Weight: 1.3 kg

This product contains light sources of energy efficiency classes E

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at: www.bega.com.

Lamp

Module connected wattage 11.5 W
Luminaire connected wattage 13.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 30 °C

50 567.1 K27

Module designation LED-0800/927
Colour temperature 2700 K
Colour rendering index CRI > 90
Module luminous flux 1665 lm
Luminaire luminous flux 1333 lm
Luminaire luminous efficiency 98,7 lm / W

50 567.1 K3

Module designation LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1735 lm
Luminaire luminous flux 1389 lm
Luminaire luminous efficiency 102,9 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove mounting plate from the luminaire housing.
Unplug the earth conductor connection (plug contact).

Please note:
If the luminaire is to be mounted onto a metallic, electroconductive surface, it is mandatory to make sure that the mounting surface is connected conductive to the earth conductor of the luminaire!
Lead the power connecting cable through the mounting plate.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Establish the earth conductor connection to the luminaire housing (plug contact).
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.

IMPORTANT:
To ensure secure connection, the luminaire housing must be positioned precisely in relation to the mounting plate.
Make sure that the vertical bar inside the luminaire housing is positioned precisely in the area of the mounting hole on the long bar of the mounting plate.
Press the luminaire housing firmly against the mounting plate and turn it clockwise firmly against the stop.

Open luminaire:
Unscrew glass from luminaire housing by turning it counter-clockwise.
To prevent the luminaire from turning on the mounting plate, hold the luminaire housing in place with one hand.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.

Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Defective glass must be replaced.
Close the luminaire.