BEGA 33 505 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 33 505 Wall Luminaire
Product Information
Product Usage Instructions
DIMENSION
Instructions for use
Cleaning Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33 505 Wall Luminaire

Product Information

Product Name: Wandleuchte Wall luminaire Applique
Model Number : 33 505
IP Rating: IP 64
Light Distribution: Two-sided
Glare: Fully glare-free
Usage: Interior or exterior lighting design

Product Usage Instructions

Safety:
- Installation and operation should comply with national safety regulations.
- Only a qualified electrician should perform installation and commissioning.
- The manufacturer is not liable for damage caused by improper use or installation.
- If modifications are made, the person responsible for the modifications is considered the manufacturer.
Lamp Details:
- Lamp Wattage: 5.8 W
- Luminaire Wattage : 6.9 W
- Rated Temperature: 25°C to 40°C
- Ambient Temperature: 33 505 K3
Module Details:
- Module Designation: 2x LED-0280/930
- Color Temperature: 3000 K
- Colour Rendering Index (CRI): >90
- Module Luminous Flux: 930 lm
- Luminaire Luminous Flux: 236 lm
- Luminaire Luminous Efficiency: 34.2 lm/W
Overvoltage Protection:
- The luminaire has built-in overvoltage protection according to DIN EN 61547.
- For additional protection, separate overvoltage protection components are recommended.
- You can find these components on the manufacturer’s website at www.bega.com.
Installation:
- Undo the screws and lift off the luminaire top.
- Avoid touching the light output opening of the LED directly during installation or relamping.
- Lead the main supply cable through the cable entry of the luminaire base.
- Note the position of the luminaire arrow, which should be pointing downwards.
- Fix the luminaire base onto the mounting surface using the appropriate fixing materials and gasket rings supplied.
- Make an earth conductor connection.
- Push silicone sleeves over the lines and make an electrical connection to the terminal (plug connection).
- Install the luminaire top, press on, and manually tighten the screws evenly.
Spares:
- LED Power Supply Unit : DEV-0304/350
- LED Module 3000 K: LED-0280/930
- LED Module 4000 K: LED-0280/940
- Gasket: 83 001 243

DIMENSION

Instructions for use

Application
Wall luminaire with two-sided light distribution opening. Fully glare-free light for lighting wall surfaces. For interior or exterior lighting design.

Product Description
Luminaire made of aluminum alloy, aluminum and stainless steel BEGA Unidure® coating technology Crystal glass with white matt finish Silicone gasket

2 mounting holes ø 4.5 mm
Distance apart 65 mm
1 cable entry for the mains supply cable
up to ø 10,5 mm
Connecting terminal 2.5@
with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 64
Dust-tight and protection against splash water Impact strength IK07
Protection against mechanical
impacts < 2 joule
r – Safety mark
c – Conformity mark
Weight: 1.0 kg

This product contains light sources of energy efficiency classes D

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 5.8 W
Luminaire connected wattage 6.9 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

33 505 K3

Module designation 2x LED-0280/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 930 lm
Luminaire luminous flux 236 lm
Luminaire luminous efficiency 34,2 lm / W

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Installation
Undo the screws and lift off the luminaire top. LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.Lead the main supply cable through the cable entry of the luminaire base. Note the position of application of the luminaire “arrow down”. Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make an earth conductor connection. Push silicone sleeves over the lines and make an electrical connection to terminal (plug connection). Install the luminaire top, press on and manually tighten the screws evenly.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high-pressure cleaners.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. The defective glass must be replaced. Close the luminaire.

Spares